Tag Archives: top

#435648 Surprisingly Speedy Soft Robot Survives ...

Posted on September 14, 2019 by Android

Soft robots are getting more and more popular for some very good reasons. Their relative simplicity is one. Their relative low cost is another. And for their simplicity and low cost, they’re generally able to perform very impressively, leveraging the unique features inherent to their design and construction to move themselves and interact with their environment. The other significant reason why soft robots are so appealing is that they’re durable. Without the constraints of rigid parts, they can withstand the sort of abuse that would make any roboticist cringe.

In the current issue of Science Robotics, a group of researchers from Tsinghua University in China and University of California, Berkeley, present a new kind of soft robot that’s both higher performance and much more robust than just about anything we’ve seen before. The deceptively simple robot looks like a bent strip of paper, but it’s able to move at 20 body lengths per second and survive being stomped on by a human wearing tennis shoes. Take that, cockroaches.

This prototype robot measures just 3 centimeters by 1.5 cm. It takes a scanning electron microscope to actually see what the robot is made of—a thermoplastic layer is sandwiched by palladium-gold electrodes, bonded with adhesive silicone to a structural plastic at the bottom. When an AC voltage (as low as 8 volts but typically about 60 volts) is run through the electrodes, the thermoplastic extends and contracts, causing the robot’s back to flex and the little “foot” to shuffle. A complete step cycle takes just 50 milliseconds, yielding a 200 hertz gait. And technically, the robot “runs,” since it does have a brief aerial phase.

Image: Science Robotics

Photos from a high-speed camera show the robot’s gait (A to D) as it contracts and expands its body.

To put the robot’s top speed of 20 body lengths per second in perspective, have a look at this nifty chart, which shows where other animals relative running speeds of some animals and robots versus body mass:

Image: Science Robotics

This chart shows the relative running speeds of some mammals (purple area), arthropods (orange area), and soft robots (blue area) versus body mass. For both mammals and arthropods, relative speeds show a strong negative scaling law with respect to the body mass: speeds increase as body masses decrease. However, for soft robots, the relationship appears to be the opposite: speeds decrease as the body mass decrease. For the little soft robots created by the researchers from Tsinghua University and UC Berkeley (red stars), the scaling law is similar to that of living animals: Higher speed was attained as the body mass decreased.

If you were wondering, like we were, just what that number 39 is on that chart (top left corner), it’s a species of tiny mite that was discovered underneath a rock in California in 1916. The mite is just under 1 mm in size, but it can run at 0.8 kilometer per hour, which is 322 body lengths per second, making it by far (like, by a factor of two at least) the fastest land animal on Earth relative to size. If a human was to run that fast relative to our size, we’d be traveling at a little bit over 2,000 kilometers per hour. It’s not a coincidence that pretty much everything in the upper left of the chart is an insect—speed scales favorably with decreasing mass, since actuators have a proportionally larger effect.

Other notable robots on the chart with impressive speed to mass ratios are number 27, which is this magnetically driven quadruped robot from UMD, and number 86, UC Berkeley’s X2-VelociRoACH.

Anyway, back to this robot. Some other cool things about it:

You can step on it, squishing it flat with a load about 1 million times its own body weight, and it’ll keep on crawling, albeit only half as fast.
Even climbing a slope of 15 degrees, it can still manage to move at 1 body length per second.
It carries peanuts! With a payload of six times its own weight, it moves a sixth as fast, but still, it’s not like you need your peanuts delivered all that quickly anyway, do you?

Image: Science Robotics

The researchers also put together a prototype with two legs instead of one, which was able to demonstrate a potentially faster galloping gait by spending more time in the air. They suggest that robots like these could be used for “environmental exploration, structural inspection, information reconnaissance, and disaster relief,” which are the sorts of things that you suggest that your robot could be used for when you really have no idea what it could be used for. But this work is certainly impressive, with speed and robustness that are largely unmatched by other soft robots. An untethered version seems possible due to the relatively low voltages required to drive the robot, and if they can put some peanut-sized sensors on there as well, practical applications might actually be forthcoming sometime soon.

“Insect-scale Fast Moving and Ultrarobust Soft Robot,” by Yichuan Wu, Justin K. Yim, Jiaming Liang, Zhichun Shao, Mingjing Qi, Junwen Zhong, Zihao Luo, Xiaojun Yan, Min Zhang, Xiaohao Wang, Ronald S. Fearing, Robert J. Full, and Liwei Lin from Tsinghua University and UC Berkeley, is published in Science Robotics. Continue reading →

Posted in Human Robots

#435634 Robot Made of Clay Can Sculpt Its Own ...

Posted on September 14, 2019 by Android

We’re very familiar with a wide variety of transforming robots—whether for submarines or drones, transformation is a way of making a single robot adaptable to different environments or tasks. Usually, these robots are restricted to a discrete number of configurations—perhaps two or three different forms—because of the constraints imposed by the rigid structures that robots are typically made of.

Soft robotics has the potential to change all this, with robots that don’t have fixed forms but instead can transform themselves into whatever shape will enable them to do what they need to do. At ICRA in Montreal earlier this year, researchers from Yale University demonstrated a creative approach toward a transforming robot powered by string and air, with a body made primarily out of clay.

Photo: Evan Ackerman

The robot is actuated by two different kinds of “skin,” one layered on top of another. There’s a locomotion skin, made of a pattern of pneumatic bladders that can roll the robot forward or backward when the bladders are inflated sequentially. On top of that is the morphing skin, which is cable-driven, and can sculpt the underlying material into a variety of shapes, including spheres, cylinders, and dumbbells. The robot itself consists of both of those skins wrapped around a chunk of clay, with the actuators driven by offboard power and control. Here it is in action:

The Yale researchers have been experimenting with morphing robots that use foams and tensegrity structures for their bodies, but that stuff provides a “restoring force,” springing back into its original shape once the actuation stops. Clay is different because it holds whatever shape it’s formed into, making the robot more energy efficient. And if the dumbbell shape stops being useful, the morphing layer can just squeeze it back into a cylinder or a sphere.

While this robot, and the sample transformation shown in the video, are relatively simplistic, the researchers suggest some ways in which a more complex version could be used in the future:

Photo: IEEE Xplore

This robot’s morphing skin sculpts its clay body into different shapes.

Applications where morphing and locomotion might serve as complementary functions are abundant. For the example skins presented in this work, a search-and-rescue operation could use the clay as a medium to hold a payload such as sensors or transmitters. More broadly, applications include resource-limited conditions where supply chains for materiel are sparse. For example, the morphing sequence shown in Fig. 4 [above] could be used to transform from a rolling sphere to a pseudo-jointed robotic arm. With such a morphing system, it would be possible to robotically morph matter into different forms to perform different functions.

Read this article for free on IEEE Xplore until 5 September 2019

Morphing Robots Using Robotic Skins That Sculpt Clay, by Dylan S. Shah, Michelle C. Yuen, Liana G. Tilton, Ellen J. Yang, and Rebecca Kramer-Bottiglio from Yale University, was presented at ICRA 2019 in Montreal.

[ Yale Faboratory ]

< Back to IEEE Journal Watch Continue reading →

Posted in Human Robots

#435601 New Double 3 Robot Makes Telepresence ...

Posted on September 12, 2019 by Android

Today, Double Robotics is announcing Double 3, the latest major upgrade to its line of consumer(ish) telepresence robots. We had a (mostly) fantastic time testing out Double 2 back in 2016. One of the things that we found out back then was that it takes a lot of practice to remotely drive the robot around. Double 3 solves this problem by leveraging the substantial advances in 3D sensing and computing that have taken place over the past few years, giving their new robot a level of intelligence that promises to make telepresence more accessible for everyone.

Double 2’s iPad has been replaced by “a fully integrated solution”—which is a fancy way of saying a dedicated 9.7-inch touchscreen and a whole bunch of other stuff. That other stuff includes an NVIDIA Jetson TX2 AI computing module, a beamforming six-microphone array, an 8-watt speaker, a pair of 13-megapixel cameras (wide angle and zoom) on a tilting mount, five ultrasonic rangefinders, and most excitingly, a pair of Intel RealSense D430 depth sensors.

It’s those new depth sensors that really make Double 3 special. The D430 modules each uses a pair of stereo cameras with a pattern projector to generate 1280 x 720 depth data with a range of between 0.2 and 10 meters away. The Double 3 robot uses all of this high quality depth data to locate obstacles, but at this point, it still doesn’t drive completely autonomously. Instead, it presents the remote operator with a slick, augmented reality view of drivable areas in the form of a grid of dots. You just click where you want the robot to go, and it will skillfully take itself there while avoiding obstacles (including dynamic obstacles) and related mishaps along the way.

This effectively offloads the most stressful part of telepresence—not running into stuff—from the remote user to the robot itself, which is the way it should be. That makes it that much easier to encourage people to utilize telepresence for the first time. The way the system is implemented through augmented reality is particularly impressive, I think. It looks like it’s intuitive enough for an inexperienced user without being restrictive, and is a clever way of mitigating even significant amounts of lag.

Otherwise, Double 3’s mobility system is exactly the same as the one featured on Double 2. In fact, that you can stick a Double 3 head on a Double 2 body and it instantly becomes a Double 3. Double Robotics is thoughtfully offering this to current Double 2 owners as a significantly more affordable upgrade option than buying a whole new robot.

For more details on all of Double 3's new features, we spoke with the co-founders of Double Robotics, Marc DeVidts and David Cann.

IEEE Spectrum: Why use this augmented reality system instead of just letting the user click on a regular camera image? Why make things more visually complicated, especially for new users?

Marc DeVidts and David Cann: One of the things that we realized about nine months ago when we got this whole thing working was that without the mixed reality for driving, it was really too magical of an experience for the customer. Even us—we had a hard time understanding whether the robot could really see obstacles and understand where the floor is and that kind of thing. So, we said “What would be the best way of communicating this information to the user?” And the right way to do it ended up drawing the graphics directly onto the scene. It’s really awesome—we have a full, real time 3D scene with the depth information drawn on top of it. We’re starting with some relatively simple graphics, and we’ll be adding more graphics in the future to help the user understand what the robot is seeing.

How robust is the vision system when it comes to obstacle detection and avoidance? Does it work with featureless surfaces, IR absorbent surfaces, in low light, in direct sunlight, etc?

We’ve looked at all of those cases, and one of the reasons that we’re going with the RealSense is the projector that helps us to see blank walls. We also found that having two sensors—one facing the floor and one facing forward—gives us a great coverage area. Having ultrasonic sensors in there as well helps us to detect anything that we can't see with the cameras. They're sort of a last safety measure, especially useful for detecting glass.

It seems like there’s a lot more that you could do with this sensing and mapping capability. What else are you working on?

We're starting with this semi-autonomous driving variant, and we're doing a private beta of full mapping. So, we’re going to do full SLAM of your environment that will be mapped by multiple robots at the same time while you're driving, and then you'll be able to zoom out to a map and click anywhere and it will drive there. That's where we're going with it, but we want to take baby steps to get there. It's the obvious next step, I think, and there are a lot more possibilities there.

Do you expect developers to be excited for this new mapping capability?

We're using a very powerful computer in the robot, a NVIDIA Jetson TX2 running Ubuntu. There's room to grow. It’s actually really exciting to be able to see, in real time, the 3D pose of the robot along with all of the depth data that gets transformed in real time into one view that gives you a full map. Having all of that data and just putting those pieces together and getting everything to work has been a huge feat in of itself.

We have an extensive API for developers to do custom implementations, either for telepresence or other kinds of robotics research. Our system isn't running ROS, but we're going to be adding ROS adapters for all of our hardware components.

Telepresence robots depend heavily on wireless connectivity, which is usually not something that telepresence robotics companies like Double have direct control over. Have you found that connectivity has been getting significantly better since you first introduced Double?

When we started in 2013, we had a lot of customers that didn’t have WiFi in their hallways, just in the conference rooms. We very rarely hear about customers having WiFi connectivity issues these days. The bigger issue we see is when people are calling into the robot from home, where they don't have proper traffic management on their home network. The robot doesn't need a ton of bandwidth, but it does need consistent, low latency bandwidth. And so, if someone else in the house is watching Netflix or something like that, it’s going to saturate your connection. But for the most part, it’s gotten a lot better over the last few years, and it’s no longer a big problem for us.

Do you think 5G will make a significant difference to telepresence robots?

We’ll see. We like the low latency possibilities and the better bandwidth, but it's all going to be a matter of what kind of reception you get. LTE can be great, if you have good reception; it’s all about where the tower is. I’m pretty sure that WiFi is going to be the primary thing for at least the next few years.

DeVidts also mentioned that an unfortunate side effect of the new depth sensors is that hanging a t-shirt on your Double to give it some personality will likely render it partially blind, so that's just something to keep in mind. To make up for this, you can switch around the colorful trim surrounding the screen, which is nowhere near as fun.

When the Double 3 is ready for shipping in late September, US $2,000 will get you the new head with all the sensors and stuff, which seamlessly integrates with your Double 2 base. Buying Double 3 straight up (with the included charging dock) will run you $4,ooo. This is by no means an inexpensive robot, and my impression is that it’s not really designed for individual consumers. But for commercial, corporate, healthcare, or education applications, $4k for a robot as capable as the Double 3 is really quite a good deal—especially considering the kinds of use cases for which it’s ideal.

[ Double Robotics ] Continue reading →

Posted in Human Robots

#435583 Soft Self-Healing Materials for Robots ...

Posted on September 11, 2019 by Android

If there’s one thing we know about robots, it’s that they break. They break, like, literally all the time. The software breaks. The hardware breaks. The bits that you think could never, ever, ever possibly break end up breaking just when you need them not to break the most, and then you have to try to explain what happened to your advisor who’s been standing there watching your robot fail and then stay up all night fixing the thing that seriously was not supposed to break.

While most of this is just a fundamental characteristic of robots that can’t be helped, the European Commission is funding a project called SHERO (Self HEaling soft RObotics) to try and solve at least some of those physical robot breaking problems through the use of structural materials that can autonomously heal themselves over and over again.

SHERO is a three year, €3 million collaboration between Vrije Universiteit Brussel, University of Cambridge, École Supérieure de Physique et de Chimie Industrielles de la ville de Paris (ESPCI-Paris), and Swiss Federal Laboratories for Materials Science and Technology (Empa). As the name SHERO suggests, the goal of the project is to develop soft materials that can completely recover from the kinds of damage that robots are likely to suffer in day to day operations, as well as the occasional more extreme accident.

Most materials, especially soft materials, are fixable somehow, whether it’s with super glue or duct tape. But fixing things involves a human first identifying when they’re broken, and then performing a potentially skill, labor, time, and money intensive task. SHERO’s soft materials will, eventually, make this entire process autonomous, allowing robots to self-identify damage and initiate healing on their own.

Photos: SHERO Project

The damaged robot finger [top] can operate normally after healing itself.

How the self-healing material works
What these self-healing materials can do is really pretty amazing. The researchers are actually developing two different types—the first one heals itself when there’s an application of heat, either internally or externally, which gives some control over when and how the healing process starts. For example, if the robot is handling stuff that’s dirty, you’d want to get it cleaned up before healing it so that dirt doesn’t become embedded in the material. This could mean that the robot either takes itself to a heating station, or it could activate some kind of embedded heating mechanism to be more self-sufficient.

The second kind of self-healing material is autonomous, in that it will heal itself at room temperature without any additional input, and is probably more suitable for relatively minor scrapes and cracks. Here are some numbers about how well the healing works:

Autonomous self-healing polymers do not require heat. They can heal damage at room temperature. Developing soft robotic systems from autonomous self-healing polymers excludes the need of additional heating devices… The healing however takes some time. The healing efficiency after 3 days, 7 days and 14 days is respectively 62 percent, 91 percent and 97 percent.

This material was used to develop a healable soft pneumatic hand. Relevant large cuts can be healed entirely without the need of external heat stimulus. Depending on the size of the damage and even more on the location of damage, the healing takes only seconds or up to a week. Damage on locations on the actuator that are subjected to very small stresses during actuation was healed instantaneously. Larger damages, like cutting the actuator completely in half, took 7 days to heal. But even this severe damage could be healed completely without the need of any external stimulus.

Applications of self-healing robots
Both of these materials can be mixed together, and their mechanical properties can be customized so that the structure that they’re a part of can be tuned to move in different ways. The researchers also plan on introducing flexible conductive sensors into the material, which will help sense damage as well as providing position feedback for control systems. A lot of development will happen over the next few years, and for more details, we spoke with Bram Vanderborght at Vrije Universiteit in Brussels.

IEEE Spectrum: How easy or difficult or expensive is it to produce these materials? Will they add significant cost to robotic grippers?

Bram Vanderborght: They are definitely more expensive materials, but it’s also a matter of size of production. At the moment, we’ve made a few kilograms of the material (enough to make several demonstrators), and the price already dropped significantly from when we ordered 100 grams of the material in the first phase of the project. So probably the cost of the gripper will be higher [than a regular gripper], but you won’t need to replace the gripper as often as other grippers that need to be replaced due to wear, so it can be an advantage.

Moreover due to the method of 3D printing the material, the surface is smoother and airtight (so no post-processing is required to make it airtight). Also, the smooth surface is better to avoid contamination for food handling, for example.

In commercial or industrial applications, gradual fatigue seems to be a more common issue than more abrupt trauma like cuts. How well does the self-healing work to improve durability over long periods of time?

We did not test for gradual fatigue over very long times. But both macroscopic and microscopic damage can be healed. So hopefully it can provide an answer here as well.

Image: SHERO Project

After developing a self-healing robot gripper, the researchers plan to use similar materials to build parts that can be used as the skeleton of robots, allowing them to repair themselves on a regular basis.

How much does the self-healing capability restrict the material properties? What are the limits for softness or hardness or smoothness or other characteristics of the material?

Typically the mechanical properties of networked polymers are much better than thermoplastics. Our material is a networked polymer but in which the crosslinks are reversible. We can change quite a lot of parameters in the design of the materials. So we can develop very stiff (fracture strain at 1.24 percent) and very elastic materials (fracture strain at 450 percent). The big advantage that our material has is we can mix it to have intermediate properties. Moreover, at the interface of the materials with different mechanical properties, we have the same chemical bonds, so the interface is perfect. While other materials, they may need to glue it, which gives local stresses and a weak spot.

When the material heals itself, is it less structurally sound in that spot? Can it heal damage that happens to the same spot over and over again?

In theory we can heal it an infinite amount of times. When the wound is not perfectly aligned, of course in that spot it will become weaker. Also too high temperatures lead to irreversible bonds, and impurities lead to weak spots.

Besides grippers and skins, what other potential robotics applications would this technology be useful for?

Most of self healing materials available now are used for coatings. What we are developing are structural components, therefore the mechanical properties of the material need to be good for such applications. So maybe part of the skeleton of the robot can be developed with such materials to make it lighter, since can be designed for regular repair. And for exceptional loads, it breaks and can be repaired like our human body.

[ SHERO Project ] Continue reading →

Posted in Human Robots

#435494 Driverless Electric Trucks Are Coming, ...

Posted on August 14, 2019 by Android

Self-driving and electric cars just don’t stop making headlines lately. Amazon invested in self-driving startup Aurora earlier this year. Waymo, Daimler, GM, along with startups like Zoox, have all launched or are planning to launch driverless taxis, many of them all-electric. People are even yanking driverless cars from their timeless natural habitat—roads—to try to teach them to navigate forests and deserts.

The future of driving, it would appear, is upon us.

But an equally important vehicle that often gets left out of the conversation is trucks; their relevance to our day-to-day lives may not be as visible as that of cars, but their impact is more profound than most of us realize.

Two recent developments in trucking point to a future of self-driving, electric semis hauling goods across the country, and likely doing so more quickly, cheaply, and safely than trucks do today.

Self-Driving in Texas
Last week, Kodiak Robotics announced it’s beginning its first commercial deliveries using self-driving trucks on a route from Dallas to Houston. The two cities sit about 240 miles apart, connected primarily by interstate 45. Kodiak is aiming to expand its reach far beyond the heart of Texas (if Dallas and Houston can be considered the heart, that is) to the state’s most far-flung cities, including El Paso to the west and Laredo to the south.

If self-driving trucks are going to be constrained to staying within state lines (and given that the laws regulating them differ by state, they will be for the foreseeable future), Texas is a pretty ideal option. It’s huge (thousands of miles of highway run both east-west and north-south), it’s warm (better than cold for driverless tech components like sensors), its proximity to Mexico means constant movement of both raw materials and manufactured goods (basically, you can’t have too many trucks in Texas), and most crucially, it’s lax on laws (driverless vehicles have been permitted there since 2017).

Spoiler, though—the trucks won’t be fully unmanned. They’ll have safety drivers to guide them onto and off of the highway, and to be there in case of any unexpected glitches.

California Goes (Even More) Electric
According to some top executives in the rideshare industry, automation is just one key component of the future of driving. Another is electricity replacing gas, and it’s not just carmakers that are plugging into the trend.

This week, Daimler Trucks North America announced completion of its first electric semis for customers Penske and NFI, to be used in the companies’ southern California operations. Scheduled to start operating later this month, the trucks will essentially be guinea pigs for testing integration of electric trucks into large-scale fleets; intel gleaned from the trucks’ performance will impact the design of later models.

Design-wise, the trucks aren’t much different from any other semi you’ve seen lumbering down the highway recently. Their range is about 250 miles—not bad if you think about how much more weight a semi is pulling than a passenger sedan—and they’ve been dubbed eCascadia, an electrified version of Freightliner’s heavy-duty Cascadia truck.

Batteries have a long way to go before they can store enough energy to make electric trucks truly viable (not to mention setting up a national charging infrastructure), but Daimler’s announcement is an important step towards an electrically-driven future.

Keep on Truckin’
Obviously, it’s more exciting to think about hailing one of those cute little Waymo cars with no steering wheel to shuttle you across town than it is to think about that 12-pack of toilet paper you ordered on Amazon cruising down the highway in a semi while the safety driver takes a snooze. But pushing driverless and electric tech in the trucking industry makes sense for a few big reasons.

Trucks mostly run long routes on interstate highways—with no pedestrians, stoplights, or other city-street obstacles to contend with, highway driving is much easier to automate. What glitches there are to be smoothed out may as well be smoothed out with cargo on board rather than people. And though you wouldn’t know it amid the frantic shouts of ‘a robot could take your job!’, the US is actually in the midst of a massive shortage of truck drivers—60,000 short as of earlier this year, to be exact.

As Todd Spencer, president of the Owner-Operator Independent Drivers Association, put it, “Trucking is an absolutely essential, critical industry to the nation, to everybody in it.” Alas, trucks get far less love than cars, but come on—probably 90 percent of the things you ate, bought, or used today were at some point moved by a truck.

Adding driverless and electric tech into that equation, then, should yield positive outcomes on all sides, whether we’re talking about cheaper 12-packs of toilet paper, fewer traffic fatalities due to human error, a less-strained labor force, a stronger economy… or something pretty cool to see as you cruise down the highway in your (driverless, electric, futuristic) car.

Image Credit: Vitpho / Shutterstock.com Continue reading →

Posted in Human Robots