Tag Archives: sony
#438769 Will Robots Make Good Friends? ...
In the 2012 film Robot and Frank, the protagonist, a retired cat burglar named Frank, is suffering the early symptoms of dementia. Concerned and guilty, his son buys him a “home robot” that can talk, do household chores like cooking and cleaning, and remind Frank to take his medicine. It’s a robot the likes of which we’re getting closer to building in the real world.
The film follows Frank, who is initially appalled by the idea of living with a robot, as he gradually begins to see the robot as both functionally useful and socially companionable. The film ends with a clear bond between man and machine, such that Frank is protective of the robot when the pair of them run into trouble.
This is, of course, a fictional story, but it challenges us to explore different kinds of human-to-robot bonds. My recent research on human-robot relationships examines this topic in detail, looking beyond sex robots and robot love affairs to examine that most profound and meaningful of relationships: friendship.
My colleague and I identified some potential risks, like the abandonment of human friends for robotic ones, but we also found several scenarios where robotic companionship can constructively augment people’s lives, leading to friendships that are directly comparable to human-to-human relationships.
Philosophy of Friendship
The robotics philosopher John Danaher sets a very high bar for what friendship means. His starting point is the “true” friendship first described by the Greek philosopher Aristotle, which saw an ideal friendship as premised on mutual good will, admiration, and shared values. In these terms, friendship is about a partnership of equals.
Building a robot that can satisfy Aristotle’s criteria is a substantial technical challenge and is some considerable way off, as Danaher himself admits. Robots that may seem to be getting close, such as Hanson Robotics’ Sophia, base their behavior on a library of pre-prepared responses: a humanoid chatbot, rather than a conversational equal. Anyone who’s had a testing back-and-forth with Alexa or Siri will know AI still has some way to go in this regard.
Aristotle also talked about other forms of “imperfect” friendship, such as “utilitarian” and “pleasure” friendships, which are considered inferior to true friendship because they don’t require symmetrical bonding and are often to one party’s unequal benefit. This form of friendship sets a relatively very low bar which some robots, like “sexbots” and robotic pets, clearly already meet.
Artificial Amigos
For some, relating to robots is just a natural extension of relating to other things in our world, like people, pets, and possessions. Psychologists have even observed how people respond naturally and socially towards media artefacts like computers and televisions. Humanoid robots, you’d have thought, are more personable than your home PC.
However, the field of “robot ethics” is far from unanimous on whether we can—or should— develop any form of friendship with robots. For an influential group of UK researchers who charted a set of “ethical principles of robotics,” human-robot “companionship” is an oxymoron, and to market robots as having social capabilities is dishonest and should be treated with caution, if not alarm. For these researchers, wasting emotional energy on entities that can only simulate emotions will always be less rewarding than forming human-to-human bonds.
But people are already developing bonds with basic robots, like vacuum-cleaning and lawn-trimming machines that can be bought for less than the price of a dishwasher. A surprisingly large number of people give these robots pet names—something they don’t do with their dishwashers. Some even take their cleaning robots on holiday.
Other evidence of emotional bonds with robots include the Shinto blessing ceremony for Sony Aibo robot dogs that were dismantled for spare parts, and the squad of US troops who fired a 21-gun salute, and awarded medals, to a bomb-disposal robot named “Boomer” after it was destroyed in action.
These stories, and the psychological evidence we have so far, make clear that we can extend emotional connections to things that are very different to us, even when we know they are manufactured and pre-programmed. But do those connections constitute a friendship comparable to that shared between humans?
True Friendship?
A colleague and I recently reviewed the extensive literature on human-to-human relationships to try to understand how, and if, the concepts we found could apply to bonds we might form with robots. We found evidence that many coveted human-to-human friendships do not in fact live up to Aristotle’s ideal.
We noted a wide range of human-to-human relationships, from relatives and lovers to parents, carers, service providers, and the intense (but unfortunately one-way) relationships we maintain with our celebrity heroes. Few of these relationships could be described as completely equal and, crucially, they are all destined to evolve over time.
All this means that expecting robots to form Aristotelian bonds with us is to set a standard even human relationships fail to live up to. We also observed forms of social connectedness that are rewarding and satisfying and yet are far from the ideal friendship outlined by the Greek philosopher.
We know that social interaction is rewarding in its own right, and something that, as social mammals, humans have a strong need for. It seems probable that relationships with robots could help to address the deep-seated urge we all feel for social connection—like providing physical comfort, emotional support, and enjoyable social exchanges—currently provided by other humans.
Our paper also discussed some potential risks. These arise particularly in settings where interaction with a robot could come to replace interaction with people, or where people are denied a choice as to whether they interact with a person or a robot—in a care setting, for instance.
These are important concerns, but they’re possibilities and not inevitabilities. In the literature we reviewed we actually found evidence of the opposite effect: robots acting to scaffold social interactions with others, acting as ice-breakers in groups, and helping people to improve their social skills or to boost their self-esteem.
It appears likely that, as time progresses, many of us will simply follow Frank’s path towards acceptance: scoffing at first, before settling into the idea that robots can make surprisingly good companions. Our research suggests that’s already happening—though perhaps not in a way of which Aristotle would have approved.
This article is republished from The Conversation under a Creative Commons license. Read the original article.
Image Credit: Andy Kelly on Unsplash Continue reading →
Posted in Human Robots
#437707 Video Friday: This Robot Will Restock ...
Video Friday is your weekly selection of awesome robotics videos, collected by your Automaton bloggers. We’ll also be posting a weekly calendar of upcoming robotics events for the next few months; here's what we have so far (send us your events!):
CLAWAR 2020 – August 24-26, 2020 – [Online Conference]
ICUAS 2020 – September 1-4, 2020 – Athens, Greece
ICRES 2020 – September 28-29, 2020 – Taipei, Taiwan
AUVSI EXPONENTIAL 2020 – October 5-8, 2020 – [Online Conference]
IROS 2020 – October 25-29, 2020 – Las Vegas, Nev., USA
CYBATHLON 2020 – November 13-14, 2020 – [Online Event]
ICSR 2020 – November 14-16, 2020 – Golden, Colo., USA
Let us know if you have suggestions for next week, and enjoy today's videos.
Tokyo startup Telexistence has recently unveiled a new robot called the Model-T, an advanced teleoperated humanoid that can use tools and grasp a wide range of objects. Japanese convenience store chain FamilyMart plans to test the Model-T to restock shelves in up to 20 stores by 2022. In the trial, a human “pilot” will operate the robot remotely, handling items like beverage bottles, rice balls, sandwiches, and bento boxes.
With Model-T and AWP, FamilyMart and TX aim to realize a completely new store operation by remoteizing and automating the merchandise restocking work, which requires a large number of labor-hours. As a result, stores can operate with less number of workers and enable them to recruit employees regardless of the store’s physical location.
[ Telexistence ]
Quadruped dance-off should be a new robotics competition at IROS or ICRA.
I dunno though, that moonwalk might keep Spot in the lead…
[ Unitree ]
Through a hybrid of simulation and real-life training, this air muscle robot is learning to play table tennis.
Table tennis requires to execute fast and precise motions. To gain precision it is necessary to explore in this high-speed regimes, however, exploration can be safety-critical at the same time. The combination of RL and muscular soft robots allows to close this gap. While robots actuated by pneumatic artificial muscles generate high forces that are required for e.g. smashing, they also offer safe execution of explosive motions due to antagonistic actuation.
To enable practical training without real balls, we introduce Hybrid Sim and Real Training (HYSR) that replays prerecorded real balls in simulation while executing actions on the real system. In this manner, RL can learn the challenging motor control of the PAM-driven robot while executing ~15000 hitting motions.
[ Max Planck Institute ]
Thanks Dieter!
Anthony Cowley wrote in to share his recent thesis work on UPSLAM, a fast and lightweight SLAM technique that records data in panoramic depth images (just PNGs) that are easy to visualize and even easier to share between robots, even on low-bandwidth networks.
[ UPenn ]
Thanks Anthony!
GITAI’s G1 is the space dedicated general-purpose robot. G1 robot will enable automation of various tasks internally & externally on space stations and for lunar base development.
[ Gitai ]
The University of Michigan has a fancy new treadmill that’s built right into the floor, which proves to be a bit much for Mini Cheetah.
But Cassie Blue won’t get stuck on no treadmill! She goes for a 0.3 mile walk across campus, which ends when a certain someone ran the gantry into Cassie Blue’s foot.
[ Michigan Robotics ]
Some serious quadruped research going on at UT Austin Human Centered Robotics Lab.
[ HCRL ]
Will Burrard-Lucas has spent lockdown upgrading his slightly indestructible BeetleCam wildlife photographing robot.
[ Will Burrard-Lucas ]
Teleoperated surgical robots are becoming commonplace in operating rooms, but many are massive (sometimes taking up an entire room) and are difficult to manipulate, especially if a complication arises and the robot needs to removed from the patient. A new collaboration between the Wyss Institute, Harvard University, and Sony Corporation has created the mini-RCM, a surgical robot the size of a tennis ball that weighs as much as a penny, and performed significantly better than manually operated tools in delicate mock-surgical procedures. Importantly, its small size means it is more comparable to the human tissues and structures on which it operates, and it can easily be removed by hand if needed.
[ Harvard Wyss ]
Yaskawa appears to be working on a robot that can scan you with a temperature gun and then jam a mask on your face?
[ Motoman ]
Maybe we should just not have people working in mines anymore, how about that?
[ Exyn ]
Many current human-robot interactive systems tend to use accurate and fast – but also costly – actuators and tracking systems to establish working prototypes that are safe to use and deploy for user studies. This paper presents an embedded framework to build a desktop space for human-robot interaction, using an open-source robot arm, as well as two RGB cameras connected to a Raspberry Pi-based controller that allow a fast yet low-cost object tracking and manipulation in 3D. We show in our evaluations that this facilitates prototyping a number of systems in which user and robot arm can commonly interact with physical objects.
[ Paper ]
IBM Research is proud to host professor Yoshua Bengio — one of the world’s leading experts in AI — in a discussion of how AI can contribute to the fight against COVID-19.
[ IBM Research ]
Ira Pastor, ideaXme life sciences ambassador interviews Professor Dr. Hiroshi Ishiguro, the Director of the Intelligent Robotics Laboratory, of the Department of Systems Innovation, in the Graduate School of Engineering Science, at Osaka University, Japan.
[ ideaXme ]
A CVPR talk from Stanford’s Chelsea Finn on “Generalization in Visuomotor Learning.”
[ Stanford ] Continue reading →
Posted in Human Robots
#436263 Skydio 2 Review: This Is the Drone You ...
Let me begin this review by saying that the Skydio 2 is one of the most impressive robots that I have ever seen. Over the last decade, I’ve spent enough time around robots to have a very good sense of what kinds of things are particularly challenging for them, and to set my expectations accordingly. Those expectations include things like “unstructured environments are basically impossible” and “full autonomy is impractically expensive” and “robot videos rarely reflect reality.”
Skydio’s newest drone is an exception to all of this. It’s able to fly autonomously at speed through complex environments in challenging real-world conditions in a way that’s completely effortless and stress-free for the end user, allowing you to capture the kind of video that would be otherwise impossible, even (I’m guessing) for professional drone pilots. When you see this technology in action, it’s (almost) indistinguishable from magic.
Skydio 2 Price
To be clear, the Skydio 2 is not without compromises, and the price of $999 (on pre-order with delivery of the next batch expected in spring of 2020) requires some justification. But the week I’ve had with this drone has left me feeling like its fundamental autonomous capability is so far beyond just about anything that I’ve ever experienced that I’m questioning why I would every fly anything else ever again.
We’ve written extensively about Skydio, beginning in early 2016 when the company posted a video of a prototype drone dodging trees while following a dude on a bike. Even three years ago, Skydio’s tech was way better than anything we’d seen outside of a research lab, and in early 2018, they introduced their first consumer product, the Skydio R1. A little over a year later, Skydio has introduced the Skydio 2, which is smaller, smarter, and much more affordable. Here’s an overview video just to get you caught up:
Skydio sent me a Skydio 2 review unit last week, and while I’m reasonably experienced with drones in general, this is the first time I’ve tried a Skydio drone in person. I had a pretty good idea what to expect, and I was absolutely blown away. Like, I was giggling to myself while running through the woods as the drone zoomed around, deftly avoiding trees and keeping me in sight. Robots aren’t supposed to be this good.
A week is really not enough time to explore everything that the Skydio can do, especially Thanksgiving week in Washington, D.C. (a no-fly zone) in early winter. But I found a nearby state park in which I could legally and safely fly the drone, and I did my best to put the Skydio 2 through its paces.
Note: Throughout this review, we’ve got a bunch of GIFs to help illustrate different features of the drone. To fit them all in, these GIFs had to be heavily compressed. Underneath each GIF is a timestamped link to this YouTube video (also available at the bottom of the post), which you can click on to see the an extended cut of the original 4K 30 fps footage. And there’s a bunch of interesting extra video in there as well.
Skydio 2 Specs
Photo: Evan Ackerman/IEEE Spectrum
The Skydio 2 is primarily made out of magnesium, which (while light) is both heavier and more rigid and durable than plastic. The offset props (the back pair are above the body, and the front pair are below) are necessary to maintain the field of view of the navigation cameras.
The Skydio 2 both looks and feels like a well-designed and carefully thought-out drone. It’s solid, and a little on the heavy side as far as drones go—it’s primarily made out of magnesium, which (while light) is both heavier and more rigid and durable than plastic. The blue and black color scheme is far more attractive than you typically see with drones.
Photo: Evan Ackerman/IEEE Spectrum
To detect and avoid obstacles, the Skydio 2 uses an array of six 4K hemispherical cameras that feed data into an NVIDIA Jetson TX2 at 30 fps, with the drone processing a million points in 3D space per second to plan the safest path.
The Skydio 2 is built around an array of six hemispherical obstacle-avoidance cameras and the NVIDIA Jetson TX2 computing module that they’re connected to. This defines the placement of the gimbal, the motors and props, and the battery, since all of this stuff has to be as much as possible out of the view of the cameras in order for the drone to effectively avoid obstacles in any direction.
Without the bottom-mounted battery attached, the drone is quite flat. The offset props (the back pair are above the body, and the front pair are below) are necessary to maintain the field of view of the obstacle-avoidance cameras. These hemispherical cameras are on the end of each of the prop arms as well as above and below the body of the drone. They look awfully exposed, even though each is protected from ground contact by a little fin. You need to make sure these cameras are clean and smudge-free, and Skydio includes a cleaning cloth for this purpose. Underneath the drone there are slots for microSD cards, one for recording from the camera and a second one that the drone uses to store data. The attention to detail extends to the SD card insertion, which has a sloped channel that guides the card securely into its slot.
Once you snap the battery in, the drone goes from looking streamlined to looking a little chubby. Relative to other drones, the battery almost seems like an afterthought, like Skydio designed the drone and then remembered, “oops we have to add a battery somewhere, let’s just kludge it onto the bottom.” But again, the reason for this is to leave room inside the body for the NVIDIA TX2, while making sure that the battery stays out of view of the obstacle avoidance cameras.
The magnetic latching system for the battery is both solid and satisfying. I’m not sure why it’s necessary, strictly speaking, but I do like it, and it doesn’t seem like the battery will fly off even during the most aggressive maneuvers. Each battery includes an LED array that will display its charge level in 25 percent increments, as well as a button that you push to turn the drone on and off. Charging takes place via a USB-C port in the top of the drone, which I don’t like, because it means that the batteries can’t be charged on their own (like the Parrot Anafi’s battery), and that you can’t charge one battery while flying with another, like basically every other drone ever. A separate battery charger that will charge two at once is available from Skydio for an eyebrow-raising $129.
I appreciate that all of Skydio’s stuff (batteries, controller, and beacon) charges via USB-C, though. The included USB-C adapter with its beefy cable will output at up to 65 watts, which’ll charge a mostly depleted battery in under an hour. The drone turns itself on while charging, which seems unnecessary.
Photo: Evan Ackerman/IEEE Spectrum
The Skydio 2 is not foldable, making it not nearly as easy to transport as some other drones. But it does come with a nice case that mitigates this issue somewhat, and the drone plus two batteries end up as a passably flat package about the size of a laptop case.
The most obvious compromise that Skydio made with the Skydio 2 is that the drone is not foldable. Skydio CEO Adam Bry told us that adding folding joints to the arms of the Skydio 2 would have made calibrating all six cameras a nightmare and significantly impacted performance. This makes complete sense, of course, but it does mean that the Skydio 2 is not nearly as easy to transport as some other drones.
Photo: Evan Ackerman/IEEE Spectrum
Folded and unfolded: The Skydio 2 compared to the Parrot Anafi (upper left) and the DJI Mavic Pro (upper right).
The Skydio 2 does come with a very nice case that mitigates this issue somewhat, and the drone plus two batteries end up as a passably flat package about the size of a laptop case. Still, it’s just not as convenient to toss into a backpack as my Anafi, although the Mavic Mini might be even more portable.
Photo: Evan Ackerman/IEEE Spectrum
While the Skydio 2’s case is relatively compact, the non-foldable drone is overall a significantly larger package than the Parrot Anafi.
The design of the drone leads to some other compromises as well. Since landing gear would, I assume, occlude the camera system, the drone lands directly on the bottom of its battery pack, which has a slightly rubberized pad about the size of a playing card. This does’t feel particularly stable unless you end up on a very flat surface, and made me concerned for the exposed cameras underneath the drone as well as the lower set of props. I’d recommend hand takeoffs and landings—more on those later.
Skydio 2 Camera System
Photo: Evan Ackerman/IEEE Spectrum
The Skydio 2’s primary camera is a Sony IMX577 1/2.3″ 12.3-megapixel CMOS sensor. It’s mounted to a three-axis gimbal and records 4K video at 60 fps, or 1080p video at 120 fps.
The Skydio 2 comes with a three-axis gimbal supporting a 12-megapixel camera, just enough to record 4K video at 60 fps, or 1080p video at 120 fps. Skydio has provided plenty of evidence that its imaging system is at least as good if not better than other drone cameras. Tested against my Mavic Pro and Parrot Anafi, I found no reason to doubt that. To be clear, I didn’t do exhaustive pixel-peeping comparisons between them, you’re just getting my subjective opinion that the Skydio 2 has a totally decent camera that you won’t be disappointed with. I will say that I found the HDR photo function to be not all that great under the few situations in which I tested it—after looking at a few muddy sunset shots, I turned it off and was much happier.
Photo: Evan Ackerman/IEEE Spectrum
The Skydio 2’s 12-megapixel camera is solid, although we weren’t impressed with the HDR option.
The video stabilization is fantastic, to the point where watching the video footage can be underwhelming because it doesn’t reflect the motion of the drone. I almost wish there was a way to change to unstabilized (or less-stabilized) video so that the viewer could get a little more of a wild ride. Or, ideally, there’d be a way for the drone to provide you with a visualization of what it was doing using the data collected by its cameras. That’s probably wishful thinking, though. The drone itself doesn’t record audio because all you’d get would be an annoying buzz, but the app does record audio, so the audio from your phone gets combined with the drone video. Don’t expect great quality, but it’s better than nothing.
Skydio 2 App
The app is very simple compared to every other drone app I’ve tried, and that’s a good thing. Here’s what it looks like:
Image: Skydio
Trackable subjects get a blue “+” sign over them, and if you tap them, the “+” turns into a spinny blue circle. Once you’ve got a subject selected, you can choose from a variety of cinematic skills that the drone will execute while following you.
You get the controls that you need and the information that you need, and nothing else. Manual flight with the on-screen buttons works adequately, and the double-tap to fly function on the phone works surprisingly well, making it easy to direct the drone to a particular spot above the ground.
The settings menus are limited but functional, allowing you to change settings for the camera and a few basic tweaks for controlling the drone. One unique setting to the Skydio 2 is the height floor—since the drone only avoids static obstacles, you can set it to maintain a height of at least 8 feet above the ground while flying autonomously to make sure that if you’re flying around other people, it won’t run into anyone who isn’t absurdly tall and therefore asking for it.
Trackable subjects get a blue “+” sign over them in the app, and if you tap them, the “+” turns into a spinny blue circle. Once you’ve got a subject selected, you can choose from a variety of cinematic skills that the drone will execute while following you, and in addition, you can select “one-shot” skills that involve the drone performing a specific maneuver before returning to the previously selected cinematic skill. For example, you can tell the drone to orbit around you, and then do a “rocket” one-shot where it’ll fly straight up above you (recording the whole time, of course), before returning to its orbiting.
After you’re done flying, you can scroll through your videos and easily clip out excerpts from them and save them to your phone for sharing. Again, it’s a fairly simple interface without a lot of options. You could call it limited, I guess, but I appreciate that it just does a few things that you care about and otherwise doesn’t clutter itself up.
The real limitation of the app is that it uses Wi-Fi to connect to the Skydio 2, which restricts the range. To fly much beyond a hundred meters or so, you’ll need to use the controller or beacon instead.
Skydio 2 Controller and Beacon
Photo: Evan Ackerman/IEEE Spectrum
While the Skydio 2 controller provides a better hands-on flight experience than with the phone, plus an extended range of up to 3.5 km, more experienced pilots may find manual control a bit frustrating, because the underlying autonomy will supersede your maneuvers when you start getting close to objects.
I was looking forward to using the controller, because with every other drone I’ve had, the precision that a physically controller provides is, I find, mandatory for a good flying experience and to get the photos and videos that you want. With Skydio 2, that’s all out the window. It’s not that the controller is useless or anything, it’s just that because the drone tracks you and avoids obstacles on its own, that level of control precision becomes largely unnecessary.
The controller itself is perfectly fine. It’s a rebranded Parrot Skycontroller3, which is the same as the one that you get with a Parrot Anafi. It’s too bad that the sticks don’t unscrew to make it a little more portable, and overall it’s functional rather than fancy, but it feels good to use and includes a sizeable antenna that makes a significant difference to the range that you get (up to 3.5 kilometers).
You definitely get a better hands-on flight experience with the controller than with the phone, so if you want to (say) zip the drone around some big open space for fun, it’s good for that. And it’s nice to be able to hand the controller to someone who’s never flown a drone before and let them take it for a spin without freaking out about them crashing it the whole time. For more experienced pilots, though, the controller is ultimately just a bit frustrating, because the underlying autonomy will supersede your control when you start getting close to objects, which (again) limits how useful the controller is relative to your phone.
I do still prefer the controller over the phone, but I’m not sure that it’s worth the extra $150, unless you plan to fly the Skydio 2 at very long distances or primarily in manual mode. And honestly, if either of those two things are your top priority, the Skydio 2 is probably not the drone for you.
Photo: Evan Ackerman/IEEE Spectrum
The Skydio 2 beacon uses GPS tracking to help the drone follow you, extending range up to 1.5 km. You can also fly the with the beacon alone, no phone necessary.
The purpose of the beacon, according to Skydio, is to give the drone a way of tracking you if it can’t see you, which can happen, albeit infrequently. My initial impression of the beacon was that it was primarily useful as a range-extending bridge between my phone and the drone. But I accidentally left my phone at home one day (oops) and had to fly the drone with only the beacon, and it was a surprisingly decent experience. The beacon allows for full manual control of a sort—you can tap different buttons to rotate, fly forward, and ascend or descend. This is sufficient for takeoff, landing, to make sure that the drone is looking at you when you engage visual tracking, and to rescue it if it gets trapped somewhere.
The rest of the beacon’s control functions are centered around a few different tracking modes, and with these, it works just about as well as your phone. You have fewer options overall, but all the basic stuff is there with just a few intuitive button clicks, including tracking range and angle. If you’re willing to deal with this relatively minor compromise, it’s nice to not have your phone available for other things rather than being monopolized by the drone.
Skydio 2 In Flight
GIF: Evan Ackerman/IEEE Spectrum
Hand takeoffs are simple and reliable.
Click here for a full resolution clip.
Starting up the Skydio 2 doesn’t require any kind of unusual calibration steps or anything like that. It prefers to be kept still, but you can start it up while holding it, it’ll just take a few seconds longer to tell you that it’s ready to go. While the drone will launch from any flat surface with significant clearance around it (it’ll tell you if it needs more room), the small footprint of the battery means that I was more comfortable hand launching it. This is not a “throw” launch; you just let the drone rest on your palm, tell it to take off, and then stay still while it gets its motors going and then gently lifts off. The lift off is so gentle that you have to be careful not to pull your hand away too soon—I did that once and the drone, being not quite ready, dropped towards the ground, but managed to recover without much drama.
GIF: Evan Ackerman/IEEE Spectrum
Hand landings always look scary, but the Skydio 2 is incredibly gentle. After trying this once, it became the only way I ever landed the drone.
Click here for a full resolution clip.
Catching the drone for landing is perhaps very slightly more dangerous, but not any more difficult. You put the drone above and in front of you facing away, tell it to land in the app or with the beacon, and then put your hand underneath it to grasp it as it slowly descends. It settles delicately and promptly turns itself off. Every drone should land this way. The battery pack provides a good place to grip, although you do have to be mindful of the forward set of props, which (since they’re the pair that are beneath the body of drone) are quite close to your fingers. You’ll certainly be mindful after you catch a blade with your fingers once. Which I did. For the purposes of this review and totally not by accident. No damage, for the record.
Photo: Evan Ackerman/IEEE Spectrum
You won’t be disappointed with the Skydio 2’s in-flight performance, unless you’re looking for a dedicated racing drone.
In normal flight, the Skydio 2 performs as well as you’d expect. It’s stable and manages light to moderate wind without any problems, although I did notice some occasional lateral drifting when the drone should have been in a stationary hover. While the controller gains are adjustable, the Skydio 2 isn’t quite as aggressive in flight as my Mavic Pro on Sport Mode, but again, if you’re looking for a high-speed drone, that’s really not what the Skydio is all about.
The Skydio 2 is substantially louder than my Anafi, although the Anafi is notably quiet for a drone. It’s not annoying to hear (not a high-pitched whine), but you can hear it from a ways away, and farther away than my Mavic Pro. I’m not sure whether that’s because of the absolute volume or the volume plus the pitch. In some ways, this is a feature, since you can hear the drone following you even if you’re not looking at it, you just need to be aware of the noise it makes when you’re flying it around people.
Obstacle Avoidance
The primary reason Skydio 2 is the drone that you want to fly is because of its autonomous subject tracking and obstacle avoidance. Skydio’s PR videos make this capability look almost too good, and since I hadn’t tried out one of their drones before, the first thing I did with it was exactly what you’d expect: attempt to fly it directly into the nearest tree.
GIF: Evan Ackerman/IEEE Spectrum
The Skydio 2 deftly slides around trees and branches. The control inputs here were simple “forward” or “turn,” all obstacle avoidance is autonomous.
Click here for a full resolution clip.
And it just won’t do it. It slows down a bit, and then slides right around one tree after another, going over and under and around branches. I pointed the drone into a forest and just held down “forward” and away it went, without any fuss, effortlessly ducking and weaving its way around. Of course, it wasn’t effortless at all—six 4K cameras were feeding data into the NVIDIA TX2 at 30 fps, and the drone was processing a million points in 3D space per second to plan the safest path while simultaneously taking into account where I wanted it to go. I spent about 10 more minutes doing my level best to crash the drone into anything at all using a flying technique probably best described as “reckless,” but the drone was utterly unfazed. It’s incredible.
What knocked my socks off was telling the drone to pass through treetops—in the clip below, I’m just telling the drone to fly straight down. Watch as it weaves its way through gaps between the branches:
GIF: Evan Ackerman/IEEE Spectrum
The result of parking the Skydio 2 above some trees and holding “down” on the controller is this impressive fully autonomous descent through the branches.
Click here for a full resolution clip.
Here’s one more example, where I sent the drone across a lake and started poking around in a tree. Sometimes the Skydio 2 isn’t sure where you want it to go, and you have to give it a little bit of a nudge in a clear direction, but that’s it.
GIF: Evan Ackerman/IEEE Spectrum
In obstacle-heavy environments, the Skydio 2 prudently slows down, but it can pick its way through almost anything that it can see.
Click here for a full resolution clip.
It’s important to keep in mind that all of the Skydio 2’s intelligence is based on vision. It uses cameras to see the world, which means that it has similar challenges as your eyes do. Specifically, Skydio warns against flying in the following conditions:
Skydio 2 can’t see certain visually challenging obstacles. Do not fly around thin branches, telephone or power lines, ropes, netting, wires, chain link fencing or other objects less than ½ inch in diameter.
Do not fly around transparent surfaces like windows or reflective surfaces like mirrors greater than 60 cm wide.
When the sun is low on the horizon, it can temporarily blind Skydio 2’s cameras depending on the angle of flight. Your drone may be cautious or jerky when flying directly toward the sun.
Basically, if you’d have trouble seeing a thing, or seeing under some specific flight conditions, then the Skydio 2 almost certainly will also. It gets even more problematic when challenging obstacles are combined with challenging flight conditions, which is what I’m pretty sure led to the only near-crash I had with the drone. Here’s a video:
GIF: Evan Ackerman/IEEE Spectrum
Flying around very thin branches and into the sun can cause problems for the Skydio 2’s obstacle avoidance.
Click here for a full resolution clip.
I had the Skydio 2 set to follow me on my bike (more about following and tracking in a bit). It was mid afternoon, but since it’s late fall here in Washington, D.C., the sun doesn’t get much higher than 30 degrees above the horizon. Late fall also means that most of the deciduous trees have lost their leaves, and so there are a bunch of skinny branches all over the place. The drone was doing a pretty good job of following me along the road at a relatively slow speed, and then it clipped the branch that you can just barely see in the video above. It recovered in an acrobatic maneuver that has been mostly video-stabilized out, and resumed tracking me before I freaked and told it to land. You can see another example here, where the drone (again) clips a branch that has the sun behind it, and this clip shows me stopping my bike before the drone runs into another branch in a similar orientation. As the video shows, it’s very hard to see the branches until it’s too late.
As far as I can tell, the drone is no worse for wear from any of this, apart from a small nick in one of the props. But, this is a good illustration of a problematic situation for the Skydio 2: flying into a low sun angle around small bare branches. Should I not have been flying the drone in this situation? It’s hard to say. These probably qualify as “thin branches,” although there was plenty of room along with middle of the road. There is an open question with the Skydio 2 as to exactly how much responsibility the user should have about when and where it’s safe to fly—for branches, how thin is too thin? How low can the sun be? What if the branches are only kinda thin and the sun is only kinda low, but it’s also a little windy? Better to be safe than sorry, of course, but there’s really no way for the user (or the drone) to know what it can’t handle until it can’t handle it.
Edge cases like these aside, the obstacle avoidance just works. Even if you’re not deliberately trying to fly into branches, it’s keeping a lookout for you all the time, which means that flying the drone goes from somewhat stressful to just pure fun. I can’t emphasize enough how amazing it is to be able to fly without worrying about running into things, and how great it feels to be able to hand the controller to someone who’s never flown a drone before and say, with complete confidence, “go ahead, fly it around!”
Skydio 2 vs. DJI Mavic
Photo: Evan Ackerman/IEEE Spectrum
Both the Skydio 2 and many models of DJI’s Mavic use visual obstacle avoidance, but the Skydio 2 is so much more advanced that you can’t really compare the two systems.
It’s important to note that there’s a huge difference between the sort of obstacle avoidance that you get with a DJI Mavic, and the sort of obstacle avoidance that you get with the Skydio 2. The objective of the Mavic’s obstacle avoidance is really there to prevent you from accidentally running into things, and in that capacity, it usually works. But there are two things to keep in mind here—first, not running into things is not the same as avoiding things, because avoiding things means planning several steps ahead, not just one step.
Second, there’s the fact that the Mavic’s obstacle detection only works most of the time. Fundamentally, I don’t trust my Mavic Pro, because sometimes the safety system doesn’t kick in for whatever reason and the drone ends up alarmingly close to something. And that’s actually fine, because with the Mavic, I expect to be piloting it. It’s for this same reason that I don’t care that my Parrot Anafi doesn’t have obstacle avoidance at all: I’m piloting it anyway, and I’m a careful pilot, so it just doesn’t matter. The Skydio 2 is totally and completely different. It’s in a class by itself, and you can’t compare what it can do to what anything else out there right now. Period.
Skydio 2 Tracking
Skydio’s big selling point on the Skydio 2 is that it’ll autonomously track you while avoiding obstacles. It does this visually, by watching where you go, predicting your future motion, and then planning its own motion to keep you in frame. The works better than you might expect, in that it’s really very good at not losing you. Obviously, the drone prioritizes not running into stuff over tracking you, which means that it may not always be where you feel like it should be. It’s probably trying to get there, but in obstacle dense environments, it can take some creative paths.
Having said that, I found it to be very consistent with keeping me in the frame, and I only managed to lose it when changing direction while fully occluded by an obstacle, or while it was executing an avoidance maneuver that was more dynamic than normal. If you deliberately try to hide from the drone it’s not that hard to do so if there are enough obstacles around, but I didn’t find the tracking to be something that I had to worry about it most cases. When tracking does fail and you’re not using the beacon, the drone will come to a hover. It won’t try and find you, but it will reacquire you if you get back into its field of view.
The Skydio 2 had no problem tracking me running through fairly dense trees:
GIF: Evan Ackerman/IEEE Spectrum
The Skydio 2 had no problem chasing me around through these trees, even while I was asking it to continually change its tracking angle.
Click here for a full resolution clip.
It also managed to keep up with me as I rode my bike along a tree-lined road:
GIF: Evan Ackerman/IEEE Spectrum
The Skydio 2 is easily fast enough to keep up with me on a bike, even while avoiding tree branches.
Click here for a full resolution clip.
It lost me when I asked it to follow very close behind me as I wove through some particularly branch-y trees, but it fails more or less gracefully by just sort of nope-ing out of situations when they start to get bad and coming to a hover somewhere safe.
GIF: Evan Ackerman/IEEE Spectrum
The Skydio 2 knows better than to put itself into situations that it can’t handle, and will bail to a safe spot if things get too complicated.
Click here for a full resolution clip.
After a few days of playing with the drone, I started to get to the point where I could set it to track me and then just forget about it while I rode my bike or whatever, as opposed to constantly turning around to make sure it was still behind me, which is what I was doing initially. It’s a level of trust that I don’t think would be possible with any other drone.
Should You Buy a Skydio 2?
Photo: Evan Ackerman/IEEE Spectrum
We think the Skydio 2 is fun and relaxing to fly, with unique autonomous intelligence that makes it worth the cost.
In case I haven’t said it often enough in this review, the Skydio 2 is an incredible piece of technology. As far as I know (as a robotics journalist, mind you), this represents the state of the art in commercial drone autonomy, and quite possibly the state of the art in drone autonomy, period. And it’s available for $999, which is expensive, but less money than a Mavic Pro 2. If you’re interested in a new drone, you should absolutely consider the Skydio 2.
There are some things to keep in mind—battery life is a solid but not stellar 20 minutes. Extra batteries are expensive at $99 each (the base kit includes just one). The controller and the beacon are also expensive, at $150 each. And while I think the Skydio 2 is definitely the drone you want to fly, it may not be the drone you want to travel with, since it’s bulky compared to other options.
But there’s no denying the fact that the experience is uniquely magical. Once you’ve flown the Skydio 2, you won’t want to fly anything else. This drone makes it possible to get pictures and videos that would be otherwise impossible, and you can do it completely on your own. You can trust the drone to do what it promises, as long as you’re mindful of some basic and common sense safety guidelines. And we’ve been told that the drone is only going to get smarter and more capable over time.
If you buy a Skydio 2, it comes with the following warranty from Skydio:
“If you’re operating your Skydio 2 within our Safe Flight guidelines, and it crashes, we’ll repair or replace it for free.”
Skydio trusts their drone to go out into a chaotic and unstructured world and dodge just about anything that comes its way. And after a week with this drone, I can see how they’re able to offer this kind of guarantee. This is the kind of autonomy that robots have been promising for years, and the Skydio 2 makes it real.
Detailed technical specifications are available on Skydio’s website, and if you have any questions, post a comment—we’ve got this drone for a little while longer, and I’d be happy to try out (nearly) anything with it.
Skydio 2 Review Video Highlights
This video is about 7 minutes of 4K, 30 fps footage directly from the Skydio 2. The only editing I did was cutting clips together, no stabilization or color correcting or anything like that. The drone will record in 4K 60 fps, so it gets smoother than this, but I, er, forgot to change the setting.
[ Skydio ] Continue reading →
Posted in Human Robots
#436234 Robot Gift Guide 2019
Welcome to the eighth edition of IEEE Spectrum’s Robot Gift Guide!
This year we’re featuring 15 robotic products that we think will make fantastic holiday gifts. As always, we tried to include a broad range of robot types and prices, focusing mostly on items released this year. (A reminder: While we provide links to places where you can buy these items, we’re not endorsing any in particular, and a little bit of research may result in better deals.)
If you need even more robot gift ideas, take a look at our past guides: 2018, 2017, 2016, 2015, 2014, 2013, and 2012. Some of those robots are still great choices and might be way cheaper now than when we first posted about them. And if you have suggestions that you’d like to share, post a comment below to help the rest of us find the perfect robot gift.
Skydio 2
Image: Skydio
What makes robots so compelling is their autonomy, and the Skydio 2 is one of the most autonomous robots we’ve ever seen. It uses an array of cameras to map its environment and avoid obstacles in real-time, making flight safe and effortless and enabling the kinds of shots that would be impossible otherwise. Seriously, this thing is magical, and it’s amazing that you can actually buy one.
$1,000
Skydio
UBTECH Jimu MeeBot 2
Image: UBTECH
The Jimu MeeBot 2.0 from UBTECH is a STEM education robot designed to be easy to build and program. It includes six servo motors, a color sensor, and LED lights. An app for iPhone or iPad provides step-by-step 3D instructions, and helps you code different behaviors for the robot. It’s available exclusively from Apple.
$130
Apple
iRobot Roomba s9+
Image: iRobot
We know that $1,400 is a crazy amount of money to spend on a robot vacuum, but the Roomba s9+ is a crazy robot vacuum. As if all of its sensors and mapping intelligence wasn’t enough, it empties itself, which means that you can have your floors vacuumed every single day for a month and you don’t have to even think about it. This is what home robots are supposed to be.
$1,400
iRobot
PFF Gita
Photo: Piaggio Fast Forward
Nobody likes carrying things, which is why Gita is perfect for everyone with an extra $3,000 lying around. Developed by Piaggio Fast Forward, this autonomous robot will follow you around with a cargo hold full of your most important stuff, and do it in a way guaranteed to attract as much attention as possible.
$3,250
Gita
DJI Mavic Mini
Photo: DJI
It’s tiny, it’s cheap, and it takes good pictures—what more could you ask for from a drone? And for $400, this is an excellent drone to get if you’re on a budget and comfortable with manual flight. Keep in mind that while the Mavic Mini is small enough that you don’t need to register it with the FAA, you do still need to follow all the same rules and regulations.
$400
DJI
LEGO Star Wars Droid Commander
Image: LEGO
Designed for kids ages 8+, this LEGO set includes more than 1,000 pieces, enough to build three different droids: R2-D2, Gonk Droid, and Mouse Droid. Using a Bluetooth-controlled robotic brick called Move Hub, which connects to the LEGO BOOST Star Wars app, kids can change how the robots behave and solve challenges, learning basic robotics and coding skills.
$200
LEGO
Sony Aibo
Photo: Sony
Robot pets don’t get much more sophisticated (or expensive) than Sony’s Aibo. Strictly speaking, it’s one of the most complex consumer robots you can buy, and Sony continues to add to Aibo’s software. Recent new features include user programmability, and the ability to “feed” it.
$2,900 (free aibone and paw pads until 12/29/2019)
Sony
Neato Botvac D4 Connected
Photo: Neato
The Neato Botvac D4 may not have all of the features of its fancier and more expensive siblings, but it does have the features that you probably care the most about: The ability to make maps of its environment for intelligent cleaning (using lasers!), along with user-defined no-go lines that keep it where you want it. And it cleans quite well, too.
$530 $350 (sale)
Neato Robotics
Cubelets Curiosity Set
Photo: Modular Robotics
Cubelets are magnetic blocks that you can snap together to make an endless variety of robots with no programming and no wires. The newest set, called Curiosity, is designed for kids ages 4+ and comes with 10 robotic cubes. These include light and distance sensors, motors, and a Bluetooth module, which connects the robot constructions to the Cubelets app.
$250
Modular Robotics
Tertill
Photo: Franklin Robotics
Tertill does one simple job: It weeds your garden. It’s waterproof, dirt proof, solar powered, and fully autonomous, meaning that you can leave it out in your garden all summer and just enjoy eating your plants rather than taking care of them.
$350
Tertill
iRobot Root
Photo: iRobot
Root was originally developed by Harvard University as a tool to help kids progressively learn to code. iRobot has taken over Root and is now supporting the curriculum, which starts for kids before they even know how to read and should keep them busy for years afterwards.
$200
iRobot
LOVOT
Image: Lovot
Let’s be honest: Nobody is really quite sure what LOVOT is. We can all agree that it’s kinda cute, though. And kinda weird. But cute. Created by Japanese robotics startup Groove X, LOVOT does have a whole bunch of tech packed into its bizarre little body and it will do its best to get you to love it.
$2,750 (¥300,000)
LOVOT
Sphero RVR
Photo: Sphero
RVR is a rugged, versatile, easy to program mobile robot. It’s a development platform designed to be a bridge between educational robots like Sphero and more sophisticated and expensive systems like Misty. It’s mostly affordable, very expandable, and comes from a company with a lot of experience making robots.
$250
Sphero
“How to Train Your Robot”
Image: Lawrence Hall of Science
Aimed at 4th and 5th graders, “How to Train Your Robot,” written by Blooma Goldberg, Ken Goldberg, and Ashley Chase, and illustrated by Dave Clegg, is a perfect introduction to robotics for kids who want to get started with designing and building robots. But the book isn’t just for beginners: It’s also a fun, inspiring read for kids who are already into robotics and want to go further—it even introduces concepts like computer simulations and deep learning. You can download a free digital copy or request hardcopies here.
Free
UC Berkeley
MIT Mini Cheetah
Photo: MIT
Yes, Boston Dynamics’ Spot, now available for lease, is probably the world’s most famous quadruped, but MIT is starting to pump out Mini Cheetahs en masse for researchers, and while we’re not exactly sure how you’d manage to get one of these things short of stealing one directly for MIT, a Mini Cheetah is our fantasy robotics gift this year. Mini Cheetah looks like a ton of fun—it’s portable, highly dynamic, super rugged, and easy to control. We want one!
Price N/A
MIT Biomimetic Robotics Lab
For more tech gift ideas, see also IEEE Spectrum’s annual Gift Guide. Continue reading →
Posted in Human Robots
#436065 From Mainframes to PCs: What Robot ...
This is a guest post. The views expressed here are solely those of the author and do not represent positions of IEEE Spectrum or the IEEE.
Autonomous robots are coming around slowly. We already got autonomous vacuum cleaners, autonomous lawn mowers, toys that bleep and blink, and (maybe) soon autonomous cars. Yet, generation after generation, we keep waiting for the robots that we all know from movies and TV shows. Instead, businesses seem to get farther and farther away from the robots that are able to do a large variety of tasks using general-purpose, human anatomy-inspired hardware.
Although these are the droids we have been looking for, anything that came close, such as Willow Garage’s PR2 or Rethink Robotics’ Baxter has bitten the dust. With building a robotic company being particularly hard, compounding business risk with technological risk, the trend goes from selling robots to selling actual services like mowing your lawn, provide taxi rides, fulfilling retail orders, or picking strawberries by the pound. Unfortunately for fans of R2-D2 and C-3PO, these kind of business models emphasize specialized, room- or fridge-sized hardware that is optimized for one very specific task, but does not contribute to a general-purpose robotic platform.
We have actually seen something very similar in the personal computer (PC) industry. In the 1950s, even though computers could be as big as an entire room and were only available to a selected few, the public already had a good idea of what computers would look like. A long list of fictional computers started to populate mainstream entertainment during that time. In a 1962 New York Times article titled “Pocket Computer to Replace Shopping List,” visionary scientist John Mauchly stated that “there is no reason to suppose the average boy or girl cannot be master of a personal computer.”
In 1968, Douglas Engelbart gave us the “mother of all demos,” browsing hypertext on a graphical screen and a mouse, and other ideas that have become standard only decades later. Now that we have finally seen all of this, it might be helpful to examine what actually enabled the computing revolution to learn where robotics is really at and what we need to do next.
The parallels between computers and robots
In the 1970s, mainframes were about to be replaced by the emerging class of mini-computers, fridge-sized devices that cost less than US $25,000 ($165,000 in 2019 dollars). These computers did not use punch-cards, but could be programmed in Fortran and BASIC, dramatically expanding the ease with which potential applications could be created. Yet it was still unclear whether mini-computers could ever replace big mainframes in applications that require fast and efficient processing of large amounts of data, let alone enter every living room. This is very similar to the robotics industry right now, where large-scale factory robots (mainframes) that have existed since the 1960s are seeing competition from a growing industry of collaborative robots that can safely work next to humans and can easily be installed and programmed (minicomputers). As in the ’70s, applications for these devices that reach system prices comparable to that of a luxury car are quite limited, and it is hard to see how they could ever become a consumer product.
Yet, as in the computer industry, successful architectures are quickly being cloned, driving prices down, and entirely new approaches on how to construct or program robotic arms are sprouting left and right. Arm makers are joined by manufacturers of autonomous carts, robotic grippers, and sensors. These components can be combined, paving the way for standard general purpose platforms that follow the model of the IBM PC, which built a capable, open architecture relying as much on commodity parts as possible.
General purpose robotic systems have not been successful for similar reasons that general purpose, also known as “personal,” computers took decades to emerge. Mainframes were custom-built for each application, while typewriters got smarter and smarter, not really leaving room for general purpose computers in between. Indeed, given the cost of hardware and the relatively little abilities of today’s autonomous robots, it is almost always smarter to build a special purpose machine than trying to make a collaborative mobile manipulator smart.
A current example is e-commerce grocery fulfillment. The current trend is to reserve underutilized parts of a brick-and-mortar store for a micro-fulfillment center that stores goods in little crates with an automated retrieval system and a (human) picker. A number of startups like Alert Innovation, Fabric, Ocado Technology, TakeOff Technologies, and Tompkins Robotics, to just name a few, have raised hundreds of millions of venture capital recently to build mainframe equivalents of robotic fulfillment centers. This is in contrast with a robotic picker, which would drive through the aisles to restock and pick from shelves. Such a robotic store clerk would come much closer to our vision of a general purpose robot, but would require many copies of itself that crowd the aisles to churn out hundreds of orders per hour as a microwarehouse could. Although eventually more efficient, the margins in retail are already low and make it unlikely that this industry will produce the technological jump that we need to get friendly C-3POs manning the aisles.
Startups have raised hundreds of millions of venture capital recently to build mainframe equivalents of robotic fulfillment centers. This is in contrast with a robotic picker, which would drive through the aisles to restock and pick from shelves, and would come much closer to our vision of a general purpose robot.
Mainframes were also attacked from the bottom. Fascination with the new digital technology has led to a hobbyist movement to create microcomputers that were sold via mail order or at RadioShack. Initially, a large number of small businesses was selling tens, at most hundreds, of devices, usually as a kit and with wooden enclosures. This trend culminated into the “1977 Trinity” in the form of the Apple II, the Commodore PET, and the Tandy TRS-80, complete computers that were sold for prices around $2500 (TRS) to $5000 (Apple) in today’s dollars. The main application of these computers was their programmability (in BASIC), which would enable consumers to “learn to chart your biorhythms, balance your checking account, or even control your home environment,” according to an original Apple advertisement. Similarly, there exists a myriad of gadgets that explore different aspects of robotics such as mobility, manipulation, and entertainment.
As in the fledgling personal computing industry, the advertised functionality was at best a model of the real deal. A now-famous milestone in entertainment robotics was the original Sony’s Aibo, a robotic dog that was advertised to have many properties that a real dog has such as develop its own personality, play with a toy, and interact with its owner. Released in 1999, and re-launched in 2018, the platform has a solid following among hobbyists and academics who like its programmability, but probably only very few users who accept the device as a pet stand-in.
There also exist countless “build-your-own-robotic-arm” kits. One of the more successful examples is the uArm, which sells for around $800, and is advertised to perform pick and place, assembly, 3D printing, laser engraving, and many other things that sound like high value applications. Using compelling videos of the robot actually doing these things in a constrained environment has led to two successful crowd-funding campaigns, and have established the robot as a successful educational tool.
Finally, there exist platforms that allow hobbyist programmers to explore mobility to construct robots that patrol your house, deliver items, or provide their users with telepresence abilities. An example of that is the Misty II. Much like with the original Apple II, there remains a disconnect between the price of the hardware and the fidelity of the applications that were available.
For computers, this disconnect began to disappear with the invention of the first electronic spreadsheet software VisiCalc that spun out of Harvard in 1979 and prompted many people to buy an entire microcomputer just to run the program. VisiCalc was soon joined by WordStar, a word processing application, that sold for close to $2000 in today’s dollars. WordStar, too, would entice many people to buy the entire hardware just to use the software. The two programs are early examples of what became known as “killer application.”
With factory automation being mature, and robots with the price tag of a minicomputer being capable of driving around and autonomously carrying out many manipulation tasks, the robotics industry is somewhere where the PC industry was between 1973—the release of the Xerox Alto, the first computer with a graphical user interface, mouse, and special software—and 1979—when microcomputers in the under $5000 category began to take off.
Killer apps for robots
So what would it take for robotics to continue to advance like computers did? The market itself already has done a good job distilling what the possible killer apps are. VCs and customers alike push companies who have set out with lofty goals to reduce their offering to a simple value proposition. As a result, companies that started at opposite ends often converge to mirror images of each other that offer very similar autonomous carts, (bin) picking, palletizing, depalletizing, or sorting solutions. Each of these companies usually serves a single application to a single vertical—for example bin-picking clothes, transporting warehouse goods, or picking strawberries by the pound. They are trying to prove that their specific technology works without spreading themselves too thin.
Very few of these companies have really taken off. One example is Kiva Systems, which turned into the logistic robotics division of Amazon. Kiva and others are structured around sound value propositions that are grounded in well-known user needs. As these solutions are very specialized, however, it is unlikely that they result into any economies of scale of the same magnitude that early computer users who bought both a spreadsheet and a word processor application for their expensive minicomputer could enjoy. What would make these robotic solutions more interesting is when functionality becomes stackable. Instead of just being able to do bin picking, palletizing, and transportation with the same hardware, these three skills could be combined to model entire processes.
A skill that is yet little addressed by startups and is historically owned by the mainframe equivalent of robotics is assembly of simple mechatronic devices. The ability to assemble mechatronic parts is equivalent to other tasks such as changing a light bulb, changing the batteries in a remote control, or tending machines like a lever-based espresso machine. These tasks would involve the autonomous execution of complete workflows possible using a single machine, eventually leading to an explosion of industrial productivity across all sectors. For example, picking up an item from a bin, arranging it on the robot, moving it elsewhere, and placing it into a shelf or a machine is a process that equally applies to a manufacturing environment, a retail store, or someone’s kitchen.
Image: Robotic Materials Inc.
Autonomous, vision and force-based assembly of the
Siemens robot learning challenge.
Even though many of the above applications are becoming possible, it is still very hard to get a platform off the ground without added components that provide “killer app” value of their own. Interesting examples are Rethink Robotics or the Robot Operating System (ROS). Rethink Robotics’ Baxter and Sawyer robots pioneered a great user experience (like the 1973 Xerox Alto, really the first PC), but its applications were difficult to extend beyond simple pick-and-place and palletizing and depalletizing items.
ROS pioneered interprocess communication software that was adapted to robotic needs (multiple computers, different programming languages) and the idea of software modularity in robotics, but—in the absence of a common hardware platform—hasn’t yet delivered a single application, e.g. for navigation, path planning, or grasping, that performs beyond research-grade demonstration level and won’t get discarded once developers turn to production systems. At the same time, an increasing number of robotic devices, such as robot arms or 3D perception systems that offer intelligent functionality, provide other ways to wire them together that do not require an intermediary computer, while keeping close control over the real-time aspects of their hardware.
Image: Robotic Materials Inc.
Robotic Materials GPR-1 combines a MIR-100 autonomous cart with an UR-5 collaborative robotic arm, an onRobot force/torque sensor and Robotic Materials’ SmartHand to perform out-of-the-box mobile assembly, bin picking, palletizing, and depalletizing tasks.
At my company, Robotic Materials Inc., we have made strides to identify a few applications such as bin picking and assembly, making them configurable with a single click by combining machine learning and optimization with an intuitive user interface. Here, users can define object classes and how to grasp them using a web browser, which then appear as first-class objects in a robot-specific graphical programming language. We have also done this for assembly, allowing users to stack perception-based picking and force-based assembly primitives by simply dragging and dropping appropriate commands together.
While such an approach might answer the question of a killer app for robots priced in the “minicomputer” range, it is unclear how killer app-type value can be generated with robots in the less-than-$5000 category. A possible answer is two-fold: First, with low-cost arms, mobility platforms, and entertainment devices continuously improving, a confluence of technology readiness and user innovation, like with the Apple II and VisiCalc, will eventually happen. For example, there is not much innovation needed to turn Misty into a home security system; the uArm into a low-cost bin-picking system; or an Aibo-like device into a therapeutic system for the elderly or children with autism.
Second, robots and their components have to become dramatically cheaper. Indeed, computers have seen an exponential reduction in price accompanied by an exponential increase in computational power, thanks in great part to Moore’s Law. This development has helped robotics too, allowing us to reach breakthroughs in mobility and manipulation due to the ability to process massive amounts of image and depth data in real-time, and we can expect it to continue to do so.
Is there a Moore’s Law for robots?
One might ask, however, how a similar dynamics might be possible for robots as a whole, including all their motors and gears, and what a “Moore’s Law” would look like for the robotics industry. Here, it helps to remember that the perpetuation of Moore’s Law is not the reason, but the result of the PC revolution. Indeed, the first killer apps for bookkeeping, editing, and gaming were so good that they unleashed tremendous consumer demand, beating the benchmark on what was thought to be physically possible over and over again. (I vividly remember 56 kbps to be the absolute maximum data rate for copper phone lines until DSL appeared.)
That these economies of scale are also applicable to mechatronics is impressively demonstrated by the car industry. A good example is the 2020 Prius Prime, a highly computerized plug-in hybrid, that is available for one third of the cost of my company’s GPR-1 mobile manipulator while being orders of magnitude more complex, sporting an electrical motor, a combustion engine, and a myriad of sensors and computers. It is therefore very well conceivable to produce a mobile manipulator that retails at one tenth of the cost of a modern car, once robotics enjoy similar mass-market appeal. Given that these robots are part of the equation, actively lowering cost of production, this might happen as fast as never before in the history of industrialization.
It is therefore very well conceivable to produce a mobile manipulator that retails at one tenth of the cost of a modern car, once robotics enjoy similar mass-market appeal.
There is one more driver that might make robots exponentially more capable: the cloud. Once a general purpose robot has learned or was programmed with a new skill, it could share it with every other robot. At some point, a grocer who buys a robot could assume that it already knows how to recognize and handle 99 percent of the retail items in the store. Likewise, a manufacturer can assume that the robot can handle and assemble every item available from McMaster-Carr and Misumi. Finally, families could expect a robot to know every kitchen item that Ikea and Pottery Barn is selling. Sounds like a labor intense problem, but probably more manageable than collecting footage for Google’s Street View using cars, tricycles, and snowmobiles, among other vehicles.
Strategies for robot startups
While we are waiting for these two trends—better and better applications and hardware with decreasing cost—to converge, we as a community have to keep exploring what the canonical robotic applications beyond mobility, bin picking, palletizing, depalletizing, and assembly are. We must also continue to solve the fundamental challenges that stand in the way of making these solutions truly general and robust.
For both questions, it might help to look at the strategies that have been critical in the development of the personal computer, which might equally well apply to robotics:
Start with a solution to a problem your customers have. Unfortunately, their problem is almost never that they need your sensor, widget, or piece of code, but something that already costs them money or negatively affects them in some other way. Example: There are many more people who had a problem calculating their taxes (and wanted to buy VisiCalc) than writing their own solution in BASIC.
Build as little of your own hardware as necessary. Your business model should be stronger than the margin you can make on the hardware. Why taking the risk? Example: Why build your own typewriter if you can write the best typewriting application that makes it worth buying a computer just for that?
If your goal is a platform, make sure it comes with a killer application, which alone justifies the platform cost. Example: Microcomputer companies came and went until the “1977 Trinity” intersected with the killer apps spreadsheet and word processors. Corollary: You can also get lucky.
Use an open architecture, which creates an ecosystem where others compete on creating better components and peripherals, while allowing others to integrate your solution into their vertical and stack it with other devices. Example: Both the Apple II and the IBM PC were completely open architectures, enabling many clones, thereby growing the user and developer base.
It’s worthwhile pursuing this. With most business processes already being digitized, general purpose robots will allow us to fill in gaps in mobility and manipulation, increasing productivity at levels only limited by the amount of resources and energy that are available, possibly creating a utopia in which creativity becomes the ultimate currency. Maybe we’ll even get R2-D2.
Nikolaus Correll is an associate professor of computer science at the University of Colorado at Boulder where he works on mobile manipulation and other robotics applications. He’s co-founder and CTO of Robotic Materials Inc., which is supported by the National Science Foundation and the National Institute of Standards and Technology via their Small Business Innovative Research (SBIR) programs. Continue reading →
Posted in Human Robots