Tag Archives: interesting

#437749 Video Friday: NASA Launches Its Most ...

Posted on November 27, 2020 by Android

Video Friday is your weekly selection of awesome robotics videos, collected by your Automaton bloggers. We’ll also be posting a weekly calendar of upcoming robotics events for the next few months; here’s what we have so far (send us your events!):

AWS Cloud Robotics Summit – August 18-19, 2020 – [Virtual Conference]
CLAWAR 2020 – August 24-26, 2020 – [Virtual Conference]
ICUAS 2020 – September 1-4, 2020 – Athens, Greece
ICRES 2020 – September 28-29, 2020 – Taipei, Taiwan
AUVSI EXPONENTIAL 2020 – October 5-8, 2020 – [Virtual Conference]
IROS 2020 – October 25-29, 2020 – Las Vegas, Nevada
ICSR 2020 – November 14-16, 2020 – Golden, Colorado
Let us know if you have suggestions for next week, and enjoy today’s videos.

Yesterday was a big day for what was quite possibly the most expensive robot on Earth up until it wasn’t on Earth anymore.

Perseverance and the Ingenuity helicopter are expected to arrive on Mars early next year.

[ JPL ]

ICYMI, our most popular post this week featured Northeastern University roboticist John Peter Whitney literally putting his neck on the line for science! He was testing a remotely operated straight razor shaving robotic system powered by fluidic actuators. The cutting-edge (sorry!) device transmits forces from a primary stage, operated by a barber, to a secondary stage, with the razor attached.

[ John Peter Whitney ]

Together with Boston Dynamics, Ford is introducing a pilot program into our Van Dyke Transmission Plant. Say hello to Fluffy the Robot Dog, who creates fast and accurate 3D scans that helps Ford engineers when we’re retooling our plants.

Not shown in the video: “At times, Fluffy sits on its robotic haunches and rides on the back of a small, round Autonomous Mobile Robot, known informally as Scouter. Scouter glides smoothly up and down the aisles of the plant, allowing Fluffy to conserve battery power until it’s time to get to work. Scouter can autonomously navigate facilities while scanning and capturing 3-D point clouds to generate a CAD of the facility. If an area is too tight for Scouter, Fluffy comes to the rescue.”

[ Ford ]

There is a thing that happens at 0:28 in this video that I have questions about.

[ Ghost Robotics ]

Pepper is far more polite about touching than most humans.

[ Paper ]

We don’t usually post pure simulation videos unless they give us something to get really, really excited about. So here’s a pure simulation video.

[ Hybrid Robotics ]

University of Michigan researchers are developing new origami inspired methods for designing, fabricating and actuating micro-robots using heat.These improvements will expand the mechanical capabilities of the tiny bots, allowing them to fold into more complex shapes.

[ DRSL ]

HMI is making beastly electric arms work underwater, even if they’re not stapled to a robotic submarine.

[ HMI ]

Here’s some interesting work in progress from MIT’s Biomimetics Robotics Lab. The limb is acting as a “virtual magnet” using a bimodal force and direction sensor.

Thanks Peter!

[ MIT Biomimetics Lab ]

This is adorable but as a former rabbit custodian I can assure you that approximately 3 seconds after this video ended, all of the wires on that robot were chewed to bits.

[ Lingkang Zhang ]

During the ARCHE 2020 integration week, TNO and the ETH Robot System Lab (RSL) collaborated to integrate their research and development process using the Articulated Locomotion and MAnipulation (ALMA) robot. Next to the integration of software, we tested software to confirm proper implementation and development. We also captured visual and auditory data for future software development. This all resulted in the creation of multiple demo’s to show the capabilities of the teleoperation framework using the ALMA robot.

[ RSL ]

When we talk about practical applications quadrupedal robots with foot wheels, we don’t usually think about them on this scale, although we should.

[ RSL ]

Juan wrote in to share a DIY quadruped that he’s been working on, named CHAMP.

Juan says that the demo robot can be built in less than US $1000 with easily accessible parts. “I hope that my project can provide a more accessible platform for students, researchers, and enthusiasts who are interested to learn more about quadrupedal robot development and its underlying technology.”

[ CHAMP ]

Thanks Juan!

Here’s a New Zealand TV report about a study on robot abuse from Christoph Bartneck at the University of Canterbury.

[ Paper ]

Our Robotics Studio is a hands on class exposing students to practical aspects of the design, fabrication, and programming of physical robotic systems. So what happens when the class goes virtual due to the covid-19 virus? Things get physical — all @ home.

[ Columbia ]

A few videos from the Supernumerary Robotic Devices Workshop, held online earlier this month.

“Handheld Robots: Bridging the Gap between Fully External and Wearable Robots,” presented by Walterio Mayol-Cuevas, University of Bristol.

“Playing the Piano with 11 Fingers: The Neurobehavioural Constraints of Human Robot Augmentation,” presented by Aldo Faisal, Imperial College London.

[ Workshop ] Continue reading →

Posted in Human Robots

#437747 High Performance Ornithopter Drone Is ...

Posted on November 27, 2020 by Android

The vast majority of drones are rotary-wing systems (like quadrotors), and for good reason: They’re cheap, they’re easy, they scale up and down well, and we’re getting quite good at controlling them, even in very challenging environments. For most applications, though, drones lose out to birds and their flapping wings in almost every way—flapping wings are very efficient, enable astonishing agility, and are much safer, able to make compliant contact with surfaces rather than shredding them like a rotor system does. But flapping wing have their challenges too: Making flapping-wing robots is so much more difficult than just duct taping spinning motors to a frame that, with a few exceptions, we haven’t seen nearly as much improvement as we have in more conventional drones.

In Science Robotics last week, a group of roboticists from Singapore, Australia, China, and Taiwan described a new design for a flapping-wing robot that offers enough thrust and control authority to make stable transitions between aggressive flight modes—like flipping and diving—while also being able to efficiently glide and gently land. While still more complex than a quadrotor in both hardware and software, this ornithopter’s advantages might make it worthwhile.

One reason that making a flapping-wing robot is difficult is because the wings have to move back and forth at high speed while electric motors spin around and around at high speed. This requires a relatively complex transmission system, which (if you don’t do it carefully), leads to weight penalties and a significant loss of efficiency. One particular challenge is that the reciprocating mass of the wings tends to cause the entire robot to flex back and forth, which alternately binds and disengages elements in the transmission system.

The researchers’ new ornithopter design mitigates the flexing problem using hinges and bearings in pairs. Elastic elements also help improve efficiency, and the ornithopter is in fact more efficient with its flapping wings than it would be with a rotary propeller-based propulsion system. Its thrust exceeds its 26-gram mass by 40 percent, which is where much of the aerobatic capability comes from. And one of the most surprising findings of this paper was that flapping-wing robots can actually be more efficient than propeller-based aircraft.

One of the most surprising findings of this paper was that flapping-wing robots can actually be more efficient than propeller-based aircraft

It’s not just thrust that’s a challenge for ornithopters: Control is much more complex as well. Like birds, ornithopters have tails, but unlike birds, they have to rely almost entirely on tail control authority, not having that bird-level of control over fine wing movements. To make an acrobatic level of control possible, the tail control surfaces on this ornithopter are huge—the tail plane area is 35 percent of the wing area. The wings can also provide some assistance in specific circumstances, as by combining tail control inputs with a deliberate stall of the things to allow the ornithopter to execute rapid flips.

With the ability to take off, hover, glide, land softly, maneuver acrobatically, fly quietly, and interact with its environment in a way that’s not (immediately) catastrophic, flapping-wing drones easily offer enough advantages to keep them interesting. Now that ornithopters been shown to be even more efficient than rotorcraft, the researchers plan to focus on autonomy with the goal of moving their robot toward real-world usefulness.

“Efficient flapping wing drone arrests high-speed flight using post-stall soaring,” by Yao-Wei Chin, Jia Ming Kok, Yong-Qiang Zhu, Woei-Leong Chan, Javaan S. Chahl, Boo Cheong Khoo, and Gih-Keong Lau from from Nanyang Technological University in Singapore, National University of Singapore, Defence Science and Technology Group in Canberra, Australia, Qingdao University of Technology in Shandong, China, University of South Australia in Mawson Lakes, and National Chiao Tung University in Hsinchu, Taiwan, was published in Science Robotics. Continue reading →

Posted in Human Robots

#437723 Minuscule RoBeetle Turns Liquid Methanol ...

Posted on November 26, 2020 by Android

It’s no secret that one of the most significant constraints on robots is power. Most robots need lots of it, and it has to come from somewhere, with that somewhere usually being a battery because there simply aren’t many other good options. Batteries, however, are famous for having poor energy density, and the smaller your robot is, the more of a problem this becomes. And the issue with batteries goes beyond the battery itself, but also carries over into all the other components that it takes to turn the stored energy into useful work, which again is a particular problem for small-scale robots.

In a paper published this week in Science Robotics, researchers from the University of Southern California, in Los Angeles, demonstrate RoBeetle, an 88-milligram four legged robot that runs entirely on methanol, a power-dense liquid fuel. Without any electronics at all, it uses an exceptionally clever bit of mechanical autonomy to convert methanol vapor directly into forward motion, one millimeter-long step at a time.

It’s not entirely clear from the video how the robot actually works, so let’s go through how it’s put together, and then look at the actuation cycle.

Image: Science Robotics

RoBeetle (A) uses a methanol-based actuation mechanism (B). The robot’s body (C) includes the fuel tank subassembly (D), a tank lid, transmission, and sliding shutter (E), bottom side of the sliding shutter (F), nickel-titanium-platinum composite wire and leaf spring (G), and front legs and hind legs with bioinspired backward-oriented claws (H).

The body of RoBeetle is a boxy fuel tank that you can fill with methanol by poking a syringe through a fuel inlet hole. It’s a quadruped, more or less, with fixed hind legs and two front legs attached to a single transmission that moves them both at once in a sort of rocking forward and up followed by backward and down motion. The transmission is hooked up to a leaf spring that’s tensioned to always pull the legs backward, such that when the robot isn’t being actuated, the spring and transmission keep its front legs more or less vertical and allow the robot to stand. Those horns are primarily there to hold the leaf spring in place, but they’ve got little hooks that can carry stuff, too.

The actuator itself is a nickel-titanium (NiTi) shape-memory alloy (SMA), which is just a wire that gets longer when it heats up and then shrinks back down when it cools. SMAs are fairly common and used for all kinds of things, but what makes this particular SMA a little different is that it’s been messily coated with platinum. The “messily” part is important for a reason that we’ll get to in just a second.

The way that the sliding vent is attached to the transmission is the really clever bit about this robot, because it means that the motion of the wire itself is used to modulate the flow of fuel through a purely mechanical system. Essentially, it’s an actuator and a sensor at the same time.

One end of the SMA wire is attached to the middle of the leaf spring, while the other end runs above the back of the robot where it’s stapled to an anchor block on the robot’s rear end. With the SMA wire hooked up but not actuated (i.e., cold rather than warm), it’s short enough that the leaf spring gets pulled back, rocking the legs forward and up. The last component is embedded in the robot’s back, right along the spine and directly underneath the SMA actuator. It’s a sliding vent attached to the transmission, so that the vent is open when the SMA wire is cold and the leaf spring is pulled back, and closed when the SMA wire is warm and the leaf spring is relaxed. The way that the sliding vent is attached to the transmission is the really clever bit about this robot, because it means that the motion of the wire itself is used to modulate the flow of fuel through a purely mechanical system. Essentially, it’s an actuator and a sensor at the same time.

The actuation cycle that causes the robot to walk begins with a full fuel tank and a cold SMA wire. There’s tension on the leaf spring, pulling the transmission back and rocking the legs forward and upward. The transmission also pulls the sliding vent into the open position, allowing methanol vapor to escape up out of the fuel tank and into the air, where it wafts past the SMA wire that runs directly above the vent.

The platinum facilitates a reaction of the methanol (CH3OH) with oxygen in the air (combustion, although not the dramatic flaming and explosive kind) to generate a couple of water molecules and some carbon dioxide plus a bunch of heat, and this is where the messy platinum coating is important, because messy means lots of surface area for the platinum to interact with as much methanol as possible. In just a second or two the temperature of the SMA wire skyrockets from 50 to 100 ºC and it expands, allowing the leaf spring about 0.1 mm of slack. As the leaf spring relaxes, the transmission moves the legs backwards and downwards, and the robot pulls itself forward about 1.2 mm. At the same time, the transmission is closing off the sliding vent, cutting off the supply of methanol vapor. Without the vapor reacting with the platinum and generating heat, in about a second and a half, the SMA wire cools down. As it does, it shrinks, pulling on the leaf spring and starting the cycle over again. Top speed is 0.76 mm/s (0.05 body-lengths per second).

An interesting environmental effect is that the speed of the robot can be enhanced by a gentle breeze. This is because air moving over the SMA wire cools it down a bit faster while also blowing away any residual methanol from around the vents, shutting down the reaction more completely. RoBeetle can carry more than its own body weight in fuel, and it takes approximately 155 minutes for a full tank of methanol to completely evaporate. It’s worth noting that despite the very high energy density of methanol, this is actually a stupendously inefficient way of powering a robot, with an estimated end-to-end efficiency of just 0.48 percent. Not 48 percent, mind you, but 0.48 percent, while in general, powering SMAs with electricity is much more efficient.

However, you have to look at the entire system that would be necessary to deliver that electricity, and for a robot as small as RoBeetle, the researchers say that it’s basically impossible. The lightest commercially available battery and power supply that would deliver enough juice to heat up an SMA actuator weighs about 800 mg, nearly 10 times the total weight of RoBeetle itself. From that perspective, RoBeetle’s efficiency is actually pretty good.

Image: A. Kitterman/Science Robotics; adapted from R.L.T./MIT

Comparison of various untethered microrobots and bioinspired soft robots that use different power and actuation strategies.

There are some other downsides to RoBeetle we should mention—it can only move forwards, not backwards, and it can’t steer. Its speed isn’t adjustable, and once it starts walking, it’ll walk until it either breaks or runs out of fuel. The researchers have some ideas about the speed, at least, pointing out that increasing the speed of fuel delivery by using pressurized liquid fuels like butane or propane would increase the actuator output frequency. And the frequency, amplitude, and efficiency of the SMAs themselves can be massively increased “by arranging multiple fiber-like thin artificial muscles in hierarchical configurations similar to those observed in sarcomere-based animal muscle,” making RoBeetle even more beetle-like.

As for sensing, RoBeetle’s 230-mg payload is enough to carry passive sensors, but getting those sensors to usefully interact with the robot itself to enable any kind of autonomy remains a challenge. Mechanically intelligence is certainly possible, though, and we can imagine RoBeetle adopting some of the same sorts of systems that have been proposed for the clockwork rover that JPL wants to use for Venus exploration. The researchers also mention how RoBeetle could potentially serve as a model for microbots capable of aerial locomotion, which is something we’d very much like to see.

“An 88-milligram insect-scale autonomous crawling robot driven by a catalytic artificial muscle,” by Xiufeng Yang, Longlong Chang, and Néstor O. Pérez-Arancibia from University of Southern California, in Los Angeles, was published in Science Robotics. Continue reading →

Posted in Human Robots

#437695 Video Friday: Even Robots Know That You ...

Posted on November 25, 2020 by Android

Video Friday is your weekly selection of awesome robotics videos, collected by your Automaton bloggers. We’ll also be posting a weekly calendar of upcoming robotics events for the next few months; here's what we have so far (send us your events!):

CLAWAR 2020 – August 24-26, 2020 – [Online Conference]
Other Than Human – September 3-10, 2020 – Stockholm, Sweden
ICRES 2020 – September 28-29, 2020 – Taipei, Taiwan
AUVSI EXPONENTIAL 2020 – October 5-8, 2020 – [Online Conference]
IROS 2020 – October 25-29, 2020 – Las Vegas, Nev., USA
CYBATHLON 2020 – November 13-14, 2020 – [Online Event]
ICSR 2020 – November 14-16, 2020 – Golden, Colo., USA
Let us know if you have suggestions for next week, and enjoy today's videos.

From the Robotics and Perception Group at UZH comes Flightmare, a simulation environment for drones that combines a slick rendering engine with a robust physics engine that can run as fast as your system can handle.

Flightmare is composed of two main components: a configurable rendering engine built on Unity and a flexible physics engine for dynamics simulation. Those two components are totally decoupled and can run independently from each other. Flightmare comes with several desirable features: (i) a large multi-modal sensor suite, including an interface to extract the 3D point-cloud of the scene; (ii) an API for reinforcement learning which can simulate hundreds of quadrotors in parallel; and (iii) an integration with a virtual-reality headset for interaction with the simulated environment. Flightmare can be used for various applications, including path-planning, reinforcement learning, visual-inertial odometry, deep learning, human-robot interaction, etc.

[ Flightmare ]

Quadruped robots yelling at people to maintain social distancing is really starting to become a thing, for better or worse.

We introduce a fully autonomous surveillance robot based on a quadruped platform that can promote social distancing in complex urban environments. Specifically, to achieve autonomy, we mount multiple cameras and a 3D LiDAR on the legged robot. The robot then uses an onboard real-time social distancing detection system to track nearby pedestrian groups. Next, the robot uses a crowd-aware navigation algorithm to move freely in highly dynamic scenarios. The robot finally uses a crowd aware routing algorithm to effectively promote social distancing by using human-friendly verbal cues to send suggestions to overcrowded pedestrians.

[ Project ]

Thanks Fan!

The Personal Robotics Group at Oregon State University is looking at UV germicidal irradiation for surface disinfection with a Fetch Manipulator Robot.

Fetch Robot disinfecting dance party woo!

[ Oregon State ]

How could you not take a mask from this robot?

[ Reachy ]

This work presents the design, development and autonomous navigation of the alpha-version of our Resilient Micro Flyer, a new type of collision-tolerant small aerial robot tailored to traversing and searching within highly confined environments including manhole-sized tubes. The robot is particularly lightweight and agile, while it implements a rigid collision-tolerant design which renders it resilient during forcible interaction with the environment. Furthermore, the design of the system is enhanced through passive flaps ensuring smoother and more compliant collision which was identified to be especially useful in very confined settings.

[ ARL ]

Pepper can make maps and autonomously navigate, which is interesting, but not as interesting as its posture when it's wandering around.

Dat backing into the charging dock tho.

[ Pepper ]

RatChair a strategy for displacing big objects by attaching relatively small vibration sources. After learning how several random bursts of vibration affect its pose, an optimization algorithm discovers the optimal sequence of vibration patterns required to (slowly but surely) move the object to a specified position.

This is from 2015, why isn't all of my furniture autonomous yet?!

[ KAIST ]

The new SeaDrone Pro is designed to be the underwater equivalent of a quadrotor. This video is a rendering, but we've been assured that it does actually exist.

[ SeaDrone ]

Thanks Eduardo!

Porous Loops is a lightweight composite facade panel that shows the potential of 3D printing of mineral foams for building scale applications.

[ ETH ]

Thanks Fan!

Here's an interesting idea for a robotic gripper- it's what appears to be a snap bracelet coupled to a pneumatic actuator that allows the snap bracelet to be reset.

[ Georgia Tech ]

Graze is developing a commercial robotic lawnmower. They're also doing a sort of crowdfunded investment thing, which probably explains the painfully overproduced nature of the following video:

A couple things about this: the hard part, which the video skips over almost entirely, is the mapping, localization, and understanding where to mow and where not to mow. The pitch deck seems to suggest that this is mostly done through computer vision, a thing that's perhaps easy to do under controlled ideal conditions, but difficult to apply to a world full lawns that are all different. The commercial aspect is interesting because golf courses are likely as standardized as you can get, but the emphasis here on how much money they can make without really addressing any of the technical stuff makes me raise an eyebrow or two.

[ Graze ]

The record & playback X-series arm demo allows the user to record the arm's movements while motors are torqued off. Then, the user may torque the motor's on and watch the movements they just made playback!

[ Interbotix ]

Shadow Robot has a new teleop system for its hand. I'm guessing that it's even trickier to use than it looks.

[ Shadow Robot ]

Quanser Interactive Labs is a collection of virtual hardware-based laboratory activities that supplement traditional or online courses. Same as working with physical systems in the lab, students work with virtual twins of Quanser's most popular plants, develop their mathematical models, implement and simulate the dynamic behavior of these systems, design controllers, and validate them on a high-fidelity 3D real-time virtual models. The virtual systems not only look like the real ones, they also behave, can be manipulated, measured, and controlled like real devices. And finally, when students go to the lab, they can deploy their virtually-validated designs on actual physical equipment.

[ Quanser ]

This video shows robot-assisted heart surgery. It's amazing to watch if you haven't seen this sort of thing before, but be aware that there is a lot of blood.

This video demonstrates a fascinating case of robotic left atrial myxoma excision, narrated by Joel Dunning, Middlesbrough, UK. The Robotic platform provides superior visualisation and enhanced dexterity, through keyhole incisions. Robotic surgery is an integral part of our Minimally Invasive Cardiothoracic Surgery Program.

[ Tristan D. Yan ]

Thanks Fan!

In this talk, we present our work on learning control policies directly in simulation that are deployed onto real drones without any fine tuning. The presentation covers autonomous drone racing, drone acrobatics, and uncertainty estimation in deep networks.

[ RPG ] Continue reading →

Posted in Human Robots

#437689 GITAI Sending Autonomous Robot to Space ...

Posted on November 24, 2020 by Android

We’ve been keeping a close watch on GITAI since early last year—what caught our interest initially is the history of the company, which includes a bunch of folks who started in the JSK Lab at the University of Tokyo, won the DARPA Robotics Challenge Trials as SCHAFT, got swallowed by Google, narrowly avoided being swallowed by SoftBank, and are now designing robots that can work in space.

The GITAI YouTube channel has kept us more to less up to date on their progress so far, and GITAI has recently announced the next step in this effort: The deployment of one of their robots on board the International Space Station in 2021.

Photo: GITAI

GITAI’s S1 is a task-specific 8-degrees-of-freedom arm with an integrated sensing and computing system and 1-meter reach.

GITAI has been working on a variety of robots for space operations, the most sophisticated of which is a humanoid torso called G1, which is controlled through an immersive telepresence system. What will be launching into space next year is a more task-specific system called the S1, which is an 8-degrees-of-freedom arm with an integrated sensing and computing system that can be wall-mounted and has a 1-meter reach.

The S1 will be living on board a commercially funded, pressurized airlock-extension module called Bishop, developed by NanoRacks. Mounted on the inside of the Bishop module, the S1 will have access to a task board and a small assembly area, where it will demonstrate common crew intra-vehicular activity, or IVA—tasks like flipping switches, turning knobs, and managing cables. It’ll also do some in-space assembly, or ISA, attaching panels to create a solar array.

Here’s a demonstration of some task board activities, conducted on Earth in a mockup of Bishop:

GITAI says that “all operations conducted by the S1 GITAI robotic arm will be autonomous, followed by some teleoperations from Nanoracks’ in-house mission control.” This is interesting, because from what we’ve seen until now, GITAI has had a heavy emphasis on telepresence, with a human in the loop to get stuff done. As GITAI’s founder and CEO Sho Nakanose commented to us a year ago, “Telepresence robots have far better performance and can be made practical much quicker than autonomous robots, so first we are working on making telepresence robots practical.”

So what’s changed? “GITAI has been concentrating on teleoperations to demonstrate the dexterity of our robot, but now it’s time to show our capabilities to do the same this time with autonomy,” Nakanose told us last week. “In an environment with minimum communication latency, it would be preferable to operate a robot more with teleoperations to enhance the capability of the robot, since with the current technology level of AI, what a robot can do autonomously is very limited. However, in an environment where the latency becomes noticeable, it would become more efficient to have a mixture of autonomy and teleoperations depending on the application. Eventually, in an ideal world, a robot will operate almost fully autonomously with minimum human cognizance.”

“In an environment where the latency becomes noticeable, it would become more efficient to have a mixture of autonomy and teleoperations depending on the application. Eventually, in an ideal world, a robot will operate almost fully autonomously with minimum human cognizance.”
—Sho Nakanose, GITAI founder and CEO

Nakanose says that this mission will help GITAI to “acquire the skills, know-how, and experience necessary to prepare a robot to be ISS compatible, prov[ing] the maturity of our technology in the microgravity environment.” Success would mean conducting both IVA and ISA experiments as planned (autonomous and teleop for IVA, fully autonomous for ISA), which would be pretty awesome, but we’re told that GITAI has already received a research and development order for space robots from a private space company, and Nakanose expects that “by the mid-2020s, we will be able to show GITAI's robots working in space on an actual mission.”

NanoRacks is schedule to launch the Bishop module on SpaceX CRS-21 in November. The S1 will be launched separately in 2021, and a NASA astronaut will install the robot and then leave it alone to let it start demonstrating how work in space can be made both safer and cheaper once the humans have gotten out of the way. Continue reading →

Posted in Human Robots